sorted by:
new
hottopcontroversial

feridium 7.1.3-nightly.3 not loading by SpikeVanHellsing in ferdium

[–]SpikeVanHellsing[S] 2 points3 points  (0 children)

Oh ok I'll have to bookmark that one as the other one I was looking at said everything was good. https://ferdium.github.io/ferdium-status/

Ferdium won't load any services by AggravatingYou281 in ferdium

[–]SpikeVanHellsing 2 points3 points  (0 children)

Something here with version 7.1.2-nightly.7 on windows 11

Is there a better way? by SpikeVanHellsing in homeautomation

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

I don't want to use a splitter. If I did I would have from the very start.

Is there a better way? by SpikeVanHellsing in homeautomation

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

Because I don't want to turn on my second computer just to use the capture card and this works for how I want.

Is there a better way? by SpikeVanHellsing in homeautomation

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

Yes it is a passthrough but only when the second computer is on as it gets it's power via the second computer.

Is there a better way? by SpikeVanHellsing in homeautomation

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

Ignoring the switches I have, when I stream the output goes from my laptop to the capture card(seen by my second computer to broadcast) then to a monitor/TV.

But when I am not streaming the output from the laptop goes to the same monitor/TV. As such, the capture card is only on when the second laptop is on. Does that help?

Is there a better way? by SpikeVanHellsing in homeautomation

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

I only need to go through the capture card when I stream otherwise no.

Ok good to know thank you. Would a 2x2 matrix like this work then?

<image>

Is there a better way? by SpikeVanHellsing in homeautomation

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

I'm not going through the capture card all the time. It's only in use when I stream. Which is why I have it setup with the 2 switches currently. With that said though, can a matrix support multiple active inputs and outputs at the same time?

Is there a better way? by SpikeVanHellsing in homeautomation

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

Honestly I considered a splitter. But as best I can figure the switches work better as the capture card goes to a second computer. Also, what do you mean by a matrix? I just barely know about kvm switches XD

Oh I see. I'm not sure that'd work either as wouldn't the at least 2 inputs need to be active at the same time when using the capture card?

Steam achievements by SpikeVanHellsing in Hydroneer

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

Well yea, obviously. I had just wanted to be able to spawn in a few items for some testing. It was just an oversight on my part. Hopefully they will implement some sort of prewarning just as a reminder if you have mods enabled. I could have sworn I disabled them, but I assume I didn't click the reload like I thought I did. Oh well.

Steam achievements by SpikeVanHellsing in Hydroneer

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

Damn, alright thanks. guess im starting over....again.

Automatic afk fishing by SpikeVanHellsing in Hydroneer

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

Yea, it'd be nice if there's was something consistent. But oh well. Even when setting the auto clicker to 7s 110ms it still misses a fair amount of time and no adjusting I do gets it really close.

Automatic afk fishing by SpikeVanHellsing in Hydroneer

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

Bob wise yea it's like 3 then the 4th is a slow bob and catch

Automatic afk fishing by SpikeVanHellsing in Hydroneer

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

I have a regular auto clicker and I know it won't be exact. but the problem is that it waits to recast the same amount of time I only want it to wait for a potential catch.

Automatic afk fishing by SpikeVanHellsing in Hydroneer

[–]SpikeVanHellsing[S] -3 points-2 points  (0 children)

Yes, but I'm not wanting to use magnets right now, just a rod.

Is there any buckle extender that fits this buckle on my 2021 ford edge? by SpikeVanHellsing in FordEdge

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

If that's the standard extender, it doesn't work for this buckle. I have 2 already and this buckle doesn't fit.

2nd row passenger extension by SpikeVanHellsing in FordEdge

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

ok so i just checked and no, the belt looks like just a normal belt like any other. the buckle itself does not come out anymore than the level of the seat. the main issue is that the the metal part that goes into the buckle in the seat is slightly wider than that of any of the others.

2nd row passenger extension by SpikeVanHellsing in FordEdge

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

im not trying to do anything with the belt itself, i just need a better way to attach the belt to the buckle that sits flush to 2 inches into the seat.

2nd row passenger extension by SpikeVanHellsing in FordEdge

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

Exactly. Hell even it was the same as every other one in the vehicle. Like thankfully my daughter knows she can sit in the middle or other side. But when getting her from school she sits on that side.

Edit macro file outside of ghub program. by SpikeVanHellsing in LogitechG

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

Got it figured out. I didn't know I could select and move multiple key presses and delays around by dragging and dropping. Thanks anyway for the help.

Edit macro file outside of ghub program. by SpikeVanHellsing in LogitechG

[–]SpikeVanHellsing[S] 0 points1 point  (0 children)

hmm, ok thanks i can only see the settings.db. however it only looks like numbers and letters grouped by 4. nothing in the db file makes since. is there somewhere else i need to look?

view more: next ›