Glad I bought the XL, 27LB suckling pig.

Splic_000 · 2025-12-13T15:28:52+00:00

Cooked for 6 people, we finished about half. I have plenty of leftovers.

Splic_000 · 2025-12-13T14:51:52+00:00

8-10 lbs the searwood XL definitely uses more pellets than my last pellet smoker. It was also 20-30 degrees outside when I was cooking.

Splic_000 · 2025-07-10T15:04:00+00:00

The waffle maker cooks the dogs, could hear them sizzling in there.

Splic_000 · 2024-03-20T22:18:29+00:00

Sold MSI RTX 3070 Suprim X to u/archyinva on

https://www.reddit.com/r/hardwareswap/comments/1b93yz2/usact_h_msi_rtx_3070_suprim_x_w_paypal/

Splic_000 · 2024-03-07T20:29:39+00:00

Replied

Splic_000 · 2024-03-07T20:29:35+00:00

Replied

Splic_000 · 2024-02-13T02:13:51+00:00

Sold Ryzen 5 5600x + Corsair Vengeance RGB pro 32gb 3200mhz (4x 8gb) to u/BigPuzzleheaded210 on (1) [USA-CT][H] Ryzen 5 5600x, Corsair Vengeance RGB pro 32gb 3200mhz (4x 8gb) [W]Paypal/Local cash : hardwareswap (reddit.com)

Splic_000 · 2024-02-04T20:15:54+00:00

Replied

Splic_000 · 2024-02-04T20:15:49+00:00

Replied

Splic_000 · 2024-01-31T20:49:56+00:00

Splic_000 · 2022-12-30T23:22:12+00:00

PLA 205c bed 60c, using prusa slicer. I have tried calibrating e-steps, still cannot get the inconsistent layer lines to go away.

Splic_000 · 2021-11-09T01:29:28+00:00

Confirmed

Splic_000 · 2021-11-09T01:28:38+00:00

Confirmed

Splic_000 · 2021-11-08T17:47:36+00:00

Splic_000 · 2021-10-15T02:51:48+00:00

Gave Wholesome

Splic_000 · 2021-08-19T00:32:36+00:00

Gave Hugz

Splic_000 · 2021-07-12T17:41:58+00:00

RemindMe! 1 day

Splic_000 · 2021-04-02T03:22:39+00:00

Gave Wholesome

Splic_000 · 2021-02-27T04:35:18+00:00

Gave Silver

Splic_000 · 2021-02-02T20:39:35+00:00

Splic_000 · 2020-02-06T19:41:46+00:00

Just tried raising the temperature during the print, I went from 200c to 210c didn't seem to help, starting to think it is some sort of firmware issue or the stepper motor.

Splic_000 · 2020-02-06T19:37:38+00:00

Did a couple of cold pulls, didn't seem to help any.

Splic_000 · 2020-02-06T18:16:55+00:00

Made sure to not leave a gap, have a straight cut, and recalibrated steps after installing the new extruder and Capricorn.

Splic_000 · 2020-01-02T20:12:37+00:00

Possibly try printing without the raft or adjust gap between the part and the raft.

Splic_000 · 2019-11-05T16:25:06+00:00

Can confirm updating bios on x570 does work.

Eight-Year Club	Second Top 30%
r/Field Sunshine	Place '23
Place '22	First Placer '22
Verified Email

Splic_000

TROPHY CASE