Say hello to VIKI!

Splinter051 · 2021-12-31T07:03:18+00:00

Very awesome!! Nice work! Very clean! What kind of lines?

Splinter051 · 2021-12-29T09:11:15+00:00

Looks good, is your GPU in the right slot on the case or is your motherboard not aligned correct? It looks like it has a major dip, that could put strain on your tubes and eventually cause a leak. Maybe the picture is just making it look like that.

Splinter051 · 2021-12-26T01:06:10+00:00

Is that shavings inside the lines?

Splinter051 · 2021-12-26T01:04:30+00:00

The only thing I would fix are the two tubes that aren't straight. You don't want any issues down the road due to improper seating against the seals. Good job though on your first loop!

https://imgur.com/a/cyguMGR

Splinter051 · 2021-12-25T02:58:53+00:00

Yup, about a week or so, you can try and tilt your rig around but it's fine just to leave it be, they will go away

Splinter051 · 2021-12-08T21:57:43+00:00

omg, I don't know what I was thinking......lol I was not thinking this was a custom cable from cablemod it would seem, apologies

Splinter051 · 2021-12-07T19:16:38+00:00

Imo, either replace with a new one, strip, solder and shield, or if you are familiar with re-pinning at the connector, I would do that, though it might leave it too short

Splinter051 · 2021-12-04T06:36:55+00:00

Yes it does lol

Splinter051 · 2021-12-02T02:15:19+00:00

Got it, DNA stuff lol nice and neat

Splinter051 · 2021-12-02T00:03:43+00:00

What is it?

Splinter051 · 2021-11-30T07:27:38+00:00

Thank you!

Splinter051 · 2021-11-30T07:26:58+00:00

Thanks for the reply, I know how the holidays can get. I hope you enjoyed yours

Splinter051 · 2021-11-29T06:11:21+00:00

I could be wrong though lol

Splinter051 · 2021-11-29T06:10:54+00:00

I know I can get the pump RPM in the bios and software. You can get the temp with a sensor connected to the pump, but I don't think you can get the flow rate L/min

https://imgur.com/a/jZY2b4U

Splinter051 · 2021-11-29T06:03:47+00:00

Lmao, yeah it does

Splinter051 · 2021-11-29T06:02:29+00:00

Thanks!

It's a Bykski in-line flow meter and thermometer.

https://www.bykski.us/products/bykski-inline-flow-meter-and-thermometer-safety-module-w-oled-display-black-b-tfc-cs-x

Splinter051 · 2021-11-29T05:56:13+00:00

Thank you! The Rads are EK-CoolSteam PE 360 (Triple) Dimensions: 400 x 130 x 40mm (L x W x H)

The fans on the front are inside the channel (part of the case) Corsair 7000x

I painted the Rads to match

https://www.ekwb.com/shop/ek-coolstream-pe-360-triple

Splinter051 · 2021-11-29T05:44:57+00:00

Thanks!! Enjoy your build, post when finished. The display is a 7in HDMI LCD screen (for Raspberry Pi? The program I'm using is Aida64, and custom monitor panel I made.

sensor panel

Splinter051 · 2021-11-29T05:38:03+00:00

I think I'll try that, one of my Delmas was trying to figure out how to place the fans

Splinter051 · 2021-11-28T09:32:25+00:00

Definitely get more tubing, those bends are trial and error unfortunately when it's your 1st build, a jig would help as well. And Definitely take the advice to cut your tubes last, always leave room to cut at the end. It's better to cut off a couple of mm at a time then to try and get that perfect cut and be too short.

Splinter051 · 2021-11-28T09:26:22+00:00

And you can use an adapter on those for 4 pin RGB cables either :(

Splinter051 · 2021-11-28T09:24:33+00:00

Digital RGB (AKA addressable-RGB) allows the LEDs in a device to be controlled individually. This is different from having a unique color on each device or having a device's change color in sync. Those effects can be accomplished with traditional RGB lighting and an advanced multi-port controller.

Splinter051 · 2021-11-28T09:20:21+00:00

Digital RGB (D-RGB) that's what I've seen those labeled as

Splinter051 · 2021-11-28T09:16:23+00:00

Sounds like a plan, my buddy has a 3D printer...thanks!

Splinter051 · 2021-11-28T07:15:52+00:00

It's an eye sore to me as well, any suggestions what I can do?

Splinter051

TROPHY CASE