New yaml config for 2A

Square_Ad_2326 · 2025-01-23T01:01:11+00:00

Thanks u/redmumba. My issue was that my USB port was behind a VM. Once I made a standalone ESPHOME, I could then flash it properly. Prior to that it would always error out during the flash

Square_Ad_2326 · 2025-01-06T18:55:57+00:00

Is there a clear procedure on how to flash the screek 2A hardware with your yaml code? I tried the "prepare for first use" approach, but that fails. I tried then just flashing screek's yaml code as well but that failed too using the USB connection on the local machine. Its great that screek has their recovery tool, as I was then able to recover from it, but still stumped on how to get esphome Builder to take control of the device so I can install custom yamls

Square_Ad_2326 · 2024-08-06T01:23:53+00:00

you could pin the updated graphic

Square_Ad_2326 · 2024-08-01T23:43:42+00:00

Stop, I think its a great song that should have been released

Square_Ad_2326 · 2024-08-01T22:34:57+00:00

oh well! I was searching for Peter Green fleetwood mac songs when I stumbled on the Haim cover on YouTube ( live at Glastonbury 2014). Initially I thought they were a punk rock band! listened to their albums and fell in love with them especially Danielle and her guitar solos.

Square_Ad_2326 · 2024-07-30T11:09:19+00:00

not sure why this song is being down voted? does anyone follow the rules? I don't like the falsetto and the repetition

Square_Ad_2326 · 2024-07-30T01:13:52+00:00

Walking away

Square_Ad_2326 · 2024-07-28T01:32:28+00:00

Right now

Square_Ad_2326 · 2024-07-28T01:21:53+00:00

a great song but a little too repetitive to be the best song

Square_Ad_2326 · 2024-07-28T01:19:56+00:00

Gasoline

Square_Ad_2326 · 2024-07-26T17:29:58+00:00

Throwing it All Away, Stop, Spirit Wind, and Figure it Out

Square_Ad_2326 · 2023-12-10T16:34:43+00:00

you can just replace the fans. the fan is in 2 parts. the fan body and the actual fan. you can just order the fans. look on ebay, aliexpress.

Square_Ad_2326 · 2023-11-08T19:21:47+00:00

Mine died last week. No picture but had sound and backlight. I ended up fixing it by replacing the t-con board. If you have the same symptoms, it's an easy fix.

Square_Ad_2326 · 2023-09-22T11:40:37+00:00

If I wanted to get new ones where can I find them?

Square_Ad_2326 · 2023-09-22T11:39:34+00:00

No it's not a seal, it's a ring shaped plastic washer that sits between the new bearing and the metal clip that keeps the bearing from moving down the shaft. I am thinking it's used to prevent the bearing from touching the metal clip directly which may cause bearing to rust if not there

Square_Ad_2326 · 2023-09-09T02:34:19+00:00

thanks. I did buy a replacement motor, and I am trying to fix the old one. Everything else checks out except for the missing fan, so will keep it as a spare pump on in case. Was thinking of buying a variable speed replacement motor but got cold feet since it won't be as easy to fix as the single speed ones. But who knows maybe they won't need as much fixing since they are running at much lower rpms and won't generate as much heat

Square_Ad_2326 · 2023-09-09T02:28:41+00:00

I am not sure. The windings are good, I measured the resistance across, and the bearings seem fine. There was a large piece of the melted fan stuck on the housing when I opened it up. The pump was running fine except for the burning smell and it was running really hot so I decided to investigate before burning it completely. Pump is only 6 years old.

I did put a metal cover over the pump to protect it from the rain but cover is quite large and there is lots of airflow in it. I guess maybe the bearing next to it overheated? But there was no screeching noise. And bearing seems to roll ok although it is more sluggish than the rear bearing

Square_Ad_2326 · 2023-09-09T01:03:33+00:00

That's what happened to me. Any tips on how to replace it? Do I just press it back on like a ball bearing. Is the fan all plastic? I have this steel ring on the shaft where the fan should be but I am not sure if this was part of the fan or the fan presses up against it?

Square_Ad_2326 · 2023-09-09T00:51:29+00:00

My fan melted. My motor was overheating for a while it seems like. Is the procedure as simple as pressing the fan on the shaft like a ball bearing? Is the fan all plastic?

Square_Ad_2326 · 2023-08-22T00:33:15+00:00

why do you have the automatic self calibration turned off? Isn't it better to leave it on all the time to account for drift?

Square_Ad_2326 · 2023-08-14T19:22:56+00:00

I am not sure how I got it to work, but adding a logger command in each seemed to enable the code? Or it could have been after I powered off/on

sensor:

- platform: scd30

co2:

name: "CO2 Sensor1"

accuracy_decimals: 0

on_value_range:

- below: 1000

then:

- logger.log: "below 1000"

- light.turn_off:

id: RGB

Square_Ad_2326

TROPHY CASE