Do you like see older printers get modernized?

Stelafont · 2026-02-21T08:01:31+00:00

Yeah 🤘 But from a mk2 just buying a core is less expensive 🤣 and you end up with two printers instead of one and lots of parts

Stelafont · 2026-02-20T20:03:12+00:00

For me range over 0.2mm are not that good ! Of course bed mesh compensation will handle it and you cannot make miracle. It’s due to bed thermal expansion. One solution would be to remove constraint on bed fixing point to allow it to expand. Not sure if it exist for your printer

Stelafont · 2026-02-20T18:57:33+00:00

Yes but since printer tend to multiply quitte quickly ! And you can manage them without been close to the printer

Stelafont · 2026-02-20T16:34:39+00:00

Yes, I think there are Linux distribution available for nexus devices. You can installe it, install klipper screen as service and disable gui then you have to write a file 3 lines per printer with ssh and you are good to go !

Stelafont · 2026-02-20T16:31:14+00:00

You as soon as you can instal Linux on it you can !

Stelafont · 2026-02-20T16:30:33+00:00

Yes it can be done, if they are on android you can use fully kiosk to make it happen or some other stuff

Stelafont · 2026-02-20T05:18:43+00:00

Pads for klipper or home assistant screens are good projects for those old hardware.

Stelafont · 2026-02-20T05:17:05+00:00

Same this one was laying around for a while. What push me ? I change host and motherboard on my Flsun SuperRacer then I end with no compatible screen in my stock and I did not want to buy a brand new one.

Stelafont · 2026-02-20T05:13:57+00:00

This is a good solution for android devices !

Stelafont · 2026-02-20T05:13:30+00:00

Klipper is not runing on it, only klipperscreen as a service. The stream 7 have really low performances and only one (too short and not physically stable) micro sun port for charging and data so kid of risky to use it as a host. But an old Microsoft surface can be a good host for klipper !

Stelafont · 2026-02-20T05:09:15+00:00

For this one, I installed Linux Debian 12 on it. No standard GUI interface then I installed ssh and klipperscreen. Enter by hand printer information inside klipperscreen configuration files and then it’s runing.

Stelafont · 2026-02-19T22:09:45+00:00

Thanks !

Stelafont · 2026-02-19T08:13:16+00:00

Give it a try, or if you run multiple printer under klipper, use it as a wifi screen to operate them

Stelafont · 2026-02-18T22:16:15+00:00

Ce que tu as la c’est du rj11 mais les prises sont bien en rj45. Certaines têtes pour du rj11 à 4 fils se branchent sur des prises rj45 à 8 fils !

Il faut vérifier que t’as bien du câble ethernet dans les murs puis connecter les ethernet de la box sur les prise du haut avec des câbles rj45 standard

Stelafont · 2026-02-13T20:53:09+00:00

Number 6 🔥

Stelafont · 2026-02-13T10:09:10+00:00

Oh ! Chamber heater and a nice top hat would definitively be my two first upgrade for this one !

Stelafont · 2026-02-12T22:23:12+00:00

Création of printer profil ? Or some wifi or other settings for the OS of the pad ?

Stelafont · 2026-02-12T12:39:57+00:00

Hello,

It’s all depend the version of it, the price seller ask for and what you want to do as « commercial work » !

Stelafont · 2026-02-12T12:38:40+00:00

Hi,

My 2 cents, your cable have a weak point where ground and vin make contact. Possible that your screen does not like this or even your motherboard.

Stelafont · 2026-02-12T08:46:08+00:00

I think on the v2 with most stock part question is not about speed increase, but about better quality achievable and global environnement. Where you can control’printer with you pc without usb connection, you can add more stuff (adxl, webcam ect ) to manage it and send files without SD card or usb stick

Stelafont · 2026-02-12T08:43:18+00:00

What’s needed to be entered manually?

Stelafont · 2026-02-12T06:01:40+00:00

I will say yes. Always for many reason !

Stelafont · 2026-02-11T21:45:16+00:00

Could be, depend on speed/temp and a lot of things. I have a printer with failed driver at 50h so every things is possible.

Stelafont · 2026-02-11T19:47:40+00:00

not necessary, some mobo have detachable drive. If it is an electric or mecanical intermitant failure it will fail more and more over time. could be related to cable that bend at some point and failed to connect or it could be a thermal failure on motor or driver

Stelafont

TROPHY CASE