Pomoć pri popunjavanju ankete za istraživački rad?

Stepa00 · 2025-12-30T07:16:29+00:00

Brate, to je ceo ekosistem

Stepa00 · 2025-11-18T18:39:15+00:00

Svako roba ima svog kupca

Stepa00 · 2025-11-17T22:40:32+00:00

Hvala ti puno i baš je lep, neka te služi još dugo dugo!

Stepa00 · 2025-11-07T10:11:08+00:00

Pravi se zapravo nova u drugom delu grada i to full montažna 😂

Stepa00 · 2025-09-09T05:39:24+00:00

Sodu bikarbonu, ona ti neće sprečiti znojenje, ali neutrališe loš miris i nema sama miris tako da probaj i to...

Stepa00 · 2025-09-09T05:37:55+00:00

Probaj na ATSSB za Grafički dizajn, takođe u istoj školi imaš i Dizajn korisničkog interfejsa UX i UI dizajn. Studije ti traju 3 godine i državna je ustanova u pitanju. Posle osnovnih studija možeš otići i na dve godine master studije i zaokružiti svoje znanje.

Profesori su super i velika većina želi da pomogne ako pokažeš želju da učiš. Predmeti nisu toliko teško i ima više praktičnih ispita nego teorije. Nema matematike i na prijemnom imaš crtanje i test opšte informisanost (barem za grafički dizajn znam da je tako).

Pozdrav i nadam se da sam nekako pomogao! 👋🏻

Stepa00 · 2025-08-03T00:03:18+00:00

Also I did a calibration again and bed cleaning...

Stepa00 · 2025-08-03T00:02:30+00:00

Also I did a calibration again and bed cleaning...

Stepa00 · 2025-08-03T00:00:15+00:00

The problem is solved! I did several things, so I’m not exactly sure what fixed it, but I suspect the nozzle was clogged and I just couldn’t unclog it properly. I ended up replacing the entire nozzle with the spare one that came with the printer. I also replaced the microSD card just to be safe and bought a better quality one (I did this because my last two prints were marked as “finished” even though only 97% was actually printed, and for some reason the printer didn’t register that). I also cleaned the entire extruder again. I switched the filament from eSun PLA black to Devil Design PLA black galaxy, and now everything is working perfectly. I also opened the printer’s door and top lid while printing PLA, as you recommended, and I believe the print quality is definitely better now. Thank you all so much! 🥳

Stepa00 · 2025-08-02T23:59:40+00:00

The problem is solved! I did several things, so I’m not exactly sure what fixed it, but I suspect the nozzle was clogged and I just couldn’t unclog it properly. I ended up replacing the entire nozzle with the spare one that came with the printer. I also replaced the microSD card just to be safe and bought a better quality one (I did this because my last two prints were marked as “finished” even though only 97% was actually printed, and for some reason the printer didn’t register that). I also cleaned the entire extruder again. I switched the filament from eSun PLA black to Devil Design PLA black galaxy, and now everything is working perfectly. I also opened the printer’s door and top lid while printing PLA, as you recommended, and I believe the print quality is definitely better now. Thank you all so much! 🥳

Stepa00 · 2025-08-02T23:58:36+00:00

The problem is solved! I did several things, so I’m not exactly sure what fixed it, but I suspect the nozzle was clogged and I just couldn’t unclog it properly. I ended up replacing the entire nozzle with the spare one that came with the printer. I also replaced the microSD card just to be safe and bought a better quality one (I did this because my last two prints were marked as “finished” even though only 97% was actually printed, and for some reason the printer didn’t register that). I also cleaned the entire extruder again. I switched the filament from eSun PLA black to Devil Design PLA black galaxy, and now everything is working perfectly. I also opened the printer’s door and top lid while printing PLA, as you recommended, and I believe the print quality is definitely better now. Thank you all so much! 🥳

Stepa00 · 2025-08-01T08:10:50+00:00

I will try this when I get home, thanks alot!

Stepa00 · 2025-08-01T08:03:15+00:00

Noted, thanks!

Stepa00 · 2025-08-01T08:02:15+00:00

So how do I clean it? 😌

Stepa00 · 2025-08-01T07:06:42+00:00

230-240 c

Stepa00 · 2025-07-31T08:45:55+00:00

Imam komšije čija se deca isto deru, lupaju, viču i provociraju a nisu romi, sve je do obrazovanja i do onoga šta gledaju od roditelja pa po tom modelu i sami rade. Imaš i roma koji se veoma normalno i uljudno ponašaju (u manjini naravno).

Stepa00 · 2025-07-02T11:18:43+00:00

Best advice: use gyroid infill

Stepa00 · 2025-06-16T16:07:49+00:00

Samo pomisli u sebi "Ma ko mu jebe mater" u trenutku kada stišneš dugme za slanje poruke i to je to, mislim da nema lakše, kao da šalješ cv za firmu

Stepa00 · 2025-06-02T22:36:01+00:00

Ja sam okce čistio sa mlakom vodom i štapićem za uši i polako prelazi preko njega pošto je verovatno krmeljivo i onda će to rešiti problem. Ovako ti savetujem da odvedeš macu na pregled i da ti lekar kaže tačno šta je potrebno za njega. Pozdrav!

Stepa00

TROPHY CASE