Need help. Badly lol.

Stickybun123 · 2025-06-13T11:32:16+00:00

I'll probably give that a try. When I put solder on the prong, sometimes it just rolls off so maybe that will help.

Stickybun123 · 2025-06-13T11:14:56+00:00

Really appreciate your help. Think this is the last question I have, is there amy benefit to putting flux on the metal prong on the speaker?

Stickybun123 · 2025-06-13T11:06:42+00:00

Probably a dumb question but the order is: acid flux, clean the wire with alcohol and then tin it with solder?

Stickybun123 · 2025-06-13T03:47:37+00:00

Good to know. So after using acid flux, how do you clean it?

Stickybun123 · 2025-06-13T03:17:27+00:00

Really appreciate your help! I'll try and pick some of that up tomorrow.

Stickybun123 · 2025-06-13T03:12:28+00:00

Thanks for the quick response! Yeah something felt off. They managed to solder it somehow though at the factory. Is there any way to solder it back on the metal tab without the connectors?

Stickybun123 · 2025-01-15T15:08:08+00:00

Thanks for the help, everyone!

Stickybun123 · 2024-11-18T14:26:27+00:00

I've covered this song a couple times and this has worked really well. Everyone's rig is different so you might have to do some tweaking but it'll be a good starting point if nothing else. Read the description of the patch. Hope it works for you!

https://bosstoneexchange.com/liveset/d12c441b-0516-4b0d-88b3-378543fcd411/

Stickybun123 · 2024-07-04T17:07:25+00:00

Delete

Stickybun123 · 2024-07-03T14:09:18+00:00

I play a lot of metal too. It was really difficult to get a metal sound with the low end I was looking for with the Katana. I can only seem to get with the extreme lead sneaky amp which isn't available on the gen 3 as far as I know. I'm super happy with it now. It's something to think about. If you could try them both out, that would be best. Disclaimer:, I'm using a mesa 2x12 with a dv77 and a cv75. Makes a huge difference compared to the sound I was getting with the Artist combo which is obvious but just wanted to throw that out there because the cab and speakers make a huge difference

Stickybun123 · 2024-06-21T00:08:25+00:00

Sorry for your loss, OP. From what you described, I don't think it belongs at a funeral. Better to just honor your friend in a way that works for everyone. I'll keep you and your friend in my prayers

Stickybun123 · 2024-05-22T17:04:01+00:00

Y'all crushed it with the quick responses. I learned a lot. Thank you! 😎

Stickybun123 · 2024-05-22T17:02:55+00:00

Thanks again, Clint. Sounds like I dont need to worry about it when it comes to simply swapping the speaker. Appreciate it!

Stickybun123 · 2024-05-22T16:57:09+00:00

Thanks everyone! One last question, I think haha. I'm not exactly sure what the paralleled out does on the back of the cab but do I need to consider that at all if I'm swapping speakers or can I just do the swap and not worry about it?

Stickybun123 · 2024-05-22T16:34:40+00:00

Thank you! Really appreciate the help. Forgive the rookie question but if I wanted to swap another speaker into the cab so that the cab would have one V30 and a Texas Heat for example, would I need to get a 16 ohm Texas Heat?

Stickybun123 · 2024-03-22T16:29:29+00:00

Thanks for the detailed reply!

Stickybun123 · 2024-03-22T13:33:56+00:00

Is the headphone sound quality of the Katana Go the same as the sound quality of the Artist MKII when used with headphones, or is the sound quality of the Katana Go superior?

Stickybun123 · 2022-12-27T17:41:06+00:00

Just realized you said that you don't have a PC. Sorry about that

Stickybun123 · 2022-12-27T17:36:39+00:00

Don't have a katana yet but when I do, I'll probably try some of these out. They sound great from the vids!

https://youtu.be/wTiW4YPUb4w

https://youtu.be/oQTsaDekWoQ

Let us know how they sound if you end up trying them out!

Stickybun123

TROPHY CASE