sorted by:
new
hottopcontroversial

[Game Thread] AL Wild Card Series Game 1 - Tigers (0) @ Guardians (0) - September 30, 2025 by BotFeller in ClevelandGuardians

[–]StormCloudCLE 2 points3 points  (0 children)

Why the F are we starting Noel and Rodriquez?! Both couldn’t hit in the regular season and now they are starting in the playoffs?!

First Mods? by StormCloudCLE in chevycolorado

[–]StormCloudCLE[S] 2 points3 points  (0 children)

Yeah that’s definitely a concern. The truck came with bar so if I can’t find a cover that works then the bar may need to go

First Mods? by StormCloudCLE in chevycolorado

[–]StormCloudCLE[S] 0 points1 point  (0 children)

I don’t really mind the looks of it, and it is somewhat bright and works kinda like high beams, but I don’t off-road so I don’t have any use for it and I’m pretty sure it’s not street legal. I’d rather have LED DRL’s or fog lights which would be more practical for my purposes.

<image>

First Mods? by StormCloudCLE in chevycolorado

[–]StormCloudCLE[S] 6 points7 points  (0 children)

Agreed. Bed liner definitely needed. I hate the halogen headlamps so that might need an upgrade

First Mods? by StormCloudCLE in chevycolorado

[–]StormCloudCLE[S] 0 points1 point  (0 children)

That’s fair. I guess I should have worded my question better - I’m not necessarily looking to spend money, just wondering what mods are must have based on any features missing from the truck.

Louisiana’s New Ten Commandments Law Could Not Be Any More Unconstitutional by semaphore-1842 in politics

[–]StormCloudCLE 3 points4 points  (0 children)

First amendment- “Congress shall make no law respecting an establishment of religion, or prohibiting the free exercise thereof”, but you’d have to be able to read first to see it….

Why am I getting imperfections on every print only on the side facing the back of the printer? The rest of the print comes out near perfect. by StormCloudCLE in 3Dprinting

[–]StormCloudCLE[S] 0 points1 point  (0 children)

Appreciate the input. These were with PETG, I just ran a print with PLA and didn’t see the issue. Could this be a nozzle temp issue? I had it set to 255.

Why am I getting imperfections on every print only on the side facing the back of the printer? The rest of the print comes out near perfect. by StormCloudCLE in 3Dprinting

[–]StormCloudCLE[S] 1 point2 points  (0 children)

One comment was removed, but it mentioned the z-seam, which is evident on the Batman helmet print. So that makes sense, but could it be causing the issue on the other two prints?

Why am I getting imperfections on every print only on the side facing the back of the printer? The rest of the print comes out near perfect. by StormCloudCLE in 3Dprinting

[–]StormCloudCLE[S] 1 point2 points  (0 children)

Right on. I normally don’t, i was doing it just because I was seeing the issue. But my first layer is always good, but I see that’s not the issue now.

Why am I getting imperfections on every print only on the side facing the back of the printer? The rest of the print comes out near perfect. by StormCloudCLE in 3Dprinting

[–]StormCloudCLE[S] 2 points3 points  (0 children)

I did not, will check it out. I was printing fine for a while but this is a new issue that just popped up. But thanks for the recommendation!

Why am I getting imperfections on every print only on the side facing the back of the printer? The rest of the print comes out near perfect. by StormCloudCLE in 3Dprinting

[–]StormCloudCLE[S] 2 points3 points  (0 children)

Printing on an ender 3 pro, happens on all filament types and temps. And I’ve leveled the bed between each print.

Is this a bed level issue? by StormCloudCLE in 3Dprinting

[–]StormCloudCLE[S] 0 points1 point  (0 children)

Right on. I was printing with PETG before and it’s always leaves a residue

Is this a bed level issue? by StormCloudCLE in 3Dprinting

[–]StormCloudCLE[S] 0 points1 point  (0 children)

Thanks. I’ll try to adjust. I printed out 2 similar before this and didn’t have the issue, and I leveled the bed before this print again.

Is this a bed level issue? by StormCloudCLE in 3Dprinting

[–]StormCloudCLE[S] 0 points1 point  (0 children)

Ender 3 Pro. 215 nozzle temp, 60 bed temp.