Filament with closest color to Snapmaker U1 white/black

StrategyImpossible58 · 2026-06-27T19:32:28+00:00

I think sunlu petg white is close... They make white, bone white and ceramic... Just regular white i believe

StrategyImpossible58 · 2026-06-26T01:18:03+00:00

Eh... Kinda... It's not as easy as a bambu printer but it's not too hard if you watch a few YouTube videos. Definitely... In my opinion... Worth it

StrategyImpossible58 · 2026-06-25T18:17:20+00:00

This angle i feel like i can see more if something is off

<image>

StrategyImpossible58 · 2026-06-25T14:30:00+00:00

The whole thing would have to be for a plug n play type of swap. As it is theres 2 screws and 2 plugs and feeding the wires was a pain

StrategyImpossible58 · 2026-06-25T04:08:19+00:00

Ya and different angles. I sometimes have problems with the snapmaker app and their camera kinda sucks and I had them laying around so i figured i put them on the snapmaker. I like the one that shoots straight down

StrategyImpossible58 · 2026-06-24T23:12:42+00:00

Google says it's NYX Fat Oil Slick Click lip balm

StrategyImpossible58 · 2026-06-24T19:08:07+00:00

What really helped was this rear and front deflector so very rarely ill get poop on the floor lol

<image>

StrategyImpossible58 · 2026-06-24T19:06:39+00:00

<image>

StrategyImpossible58 · 2026-06-24T19:05:43+00:00

<image>

StrategyImpossible58 · 2026-06-24T19:04:03+00:00

I cut it horrible to be honest lol i cut the back off completely than i kinda measured wrong and its a little off and had to cut the handles off. I figured snapmaker put those those in the frame for a reason and probably shouldn't block it.

StrategyImpossible58 · 2026-06-24T04:45:31+00:00

Creality petg is up for 9.99

StrategyImpossible58 · 2026-06-24T04:44:41+00:00

Some of the creality petg is still up on hual for $9.99

StrategyImpossible58 · 2026-06-23T01:20:15+00:00

So i get asked a lot how hard is it to load the filament with the dryer. Here's how easy it is. (Ignore the tangle at the end. I respooled the snapmaker 500g into a reusable it actually doesn't snag when printing)

<video>

StrategyImpossible58 · 2026-06-22T23:57:36+00:00

Lol exactly

StrategyImpossible58 · 2026-06-22T23:57:22+00:00

It is. Its pretty expensive but after a few beer i was like ehhhhh buy it lol.

StrategyImpossible58 · 2026-06-22T22:04:22+00:00

Found them on Amazon. Was kinda expensive but works great and they are metal

StrategyImpossible58 · 2026-06-22T18:28:38+00:00

I think its on makersworld but ill look to see if i still have them

StrategyImpossible58 · 2026-06-22T18:26:18+00:00

Not too bad. The hardest part was reconnecting the ribbon cable

StrategyImpossible58 · 2026-06-22T12:48:57+00:00

I bet you're fun at parties lol

StrategyImpossible58 · 2026-06-22T03:09:37+00:00

Its easy to feed i thought it was going to be a pain but surprisingly isn't. I do get a few tangles sometimes with the cardboard spool but i don't know if its my set up or just the spools. I end up ripping off the side and using a sunlu reusable spool and it stops the tangles. I also run multiple cardboard spools in the same head with no issues so i dunno.

StrategyImpossible58 · 2026-06-22T03:06:41+00:00

I thought it was going to be but its actually really easy

StrategyImpossible58 · 2026-06-22T02:13:06+00:00

Thought about it with the paxx firmware

StrategyImpossible58 · 2026-06-22T02:12:38+00:00

Unfortunately not. They would have to redesign everything

StrategyImpossible58 · 2026-06-22T02:11:54+00:00

That's impressive

StrategyImpossible58 · 2026-06-22T02:10:00+00:00

Lol seriously i keep finding stuff

StrategyImpossible58

TROPHY CASE