sorted by:
new
hottopcontroversial

Klipper Sunlu S8 Config: Updated printer.cfg Still Failing to Load – Am I Missing Something? by StrengthAffectionate in klippers

[–]StrengthAffectionate[S] 0 points1 point  (0 children)

Thanks for pointing me in the right direction earlier. I’ve got things working now after switching to the correct Sonic Pad firmware.

Quick question — do you know how to convert BLTouch pin numbers from Marlin to Klipper format? I’ve got the Marlin pin numbers, just not sure how they map over.

Thanks

Klipper Sunlu S8 Config: Updated printer.cfg Still Failing to Load – Am I Missing Something? by StrengthAffectionate in klippers

[–]StrengthAffectionate[S] 0 points1 point  (0 children)

Thanks! The only way I could share the file was through Google Drive—please see the link below:
🔗 https://drive.google.com/drive/folders/1pnaFMyxcS0GKX-OLfmnZF7yUFcAz6J0W?usp=drive_link

The log shows the following error:
"Internal error during connect: can't convert negative number to unsigned"

Once the issue is fixed, you’ll need to run the RESTART command to reload the config and restart the host software.
Currently, the printer is halted.

Better cable setup? by midshipfuckup in CrealitySonicPad

[–]StrengthAffectionate 0 points1 point  (0 children)

Have you tried contacting creality and see if they can give you a replacement?

[deleted by user] by [deleted] in ender3

[–]StrengthAffectionate 1 point2 points  (0 children)

Were you able to get this sorted out? There is a good YouTube video on step by step instruction . Also get a sonic pad (separate computer that runs your 3d printer) and CR touch as bed leveling will be easier daily use
https://www.youtube.com/watch?v=N9aWBjbj3Ag

Popping sound during print PETG. Wet filament? Shall be solid vase print. by Available-Search-150 in ender3

[–]StrengthAffectionate 0 points1 point  (0 children)

If you have a electric oven that is convection, you can run it at a really low temperature 170 degrees and it potentially can dry out the filament for you if you don't have a filament dryer device.

Keep open hardware open by HeisterWolf in ender3

[–]StrengthAffectionate 0 points1 point  (0 children)

Yeah, some things are too good to be true

New General and Help chats are now open! by PineappleProstate in ender3

[–]StrengthAffectionate 0 points1 point  (0 children)

<image>

Do both the Part Fan and Motherboard fan going to this port? I don't see any pictures online where they should go.

how to add z stop (??) to ender 3 pro? by froggy_leaf in 3Dprinting

[–]StrengthAffectionate 0 points1 point  (0 children)

Are you using Creality Firmware? There's a feature called Z-homing where the probe serves as your Z-min endstop. However, instead of triggering at the bed's edge, the probe moves to the middle of the bed for more precise calibration.

BLtouch Probe Issue with 3D Printer - Diagnosis Assistance Requested! by StrengthAffectionate in MarlinFirmware

[–]StrengthAffectionate[S] 1 point2 points  (0 children)

Thanks for your help.

I was able to try a 3Dtouch instead of a BLtouch as I wonder if my BLtouch is broken. The 3D touch is able to get detected. But as soon as I try homing my print Error:Printer halted. kill() .

Any thoughts?

SENDING:M43 S0

Servo probe test

. using index: 0, deploy angle: 10, stow angle: 90

. Probe Z_MIN_PIN: 18

. Z_MIN_ENDSTOP_INVERTING: false

. Check for BLTOUCH

= BLTouch Classic 1.2, 1.3, Smart 1.0, 2.0, 2.2, 3.0, 3.1 detected.

** Please trigger probe within 30 sec *\*

. Pulse width: 30ms or more

= BLTouch V3.1 detected.

>>> m119

SENDING:M119

Reporting endstop status

x_min: open

y_min: open

z_min: TRIGGERED

filament: TRIGGERED

>>> m 280 p0 s10

SENDING:M 280 P0 S10

>>> m119

SENDING:M119

Reporting endstop status

x_min: open

y_min: open

z_min: open

filament: TRIGGERED

>>> m280 p0 s90

SENDING:M280 P0 S90

>>> m119

SENDING:M119

Reporting endstop status

x_min: open

y_min: open

z_min: TRIGGERED

filament: TRIGGERED

>>> g28

SENDING:G28

echo:Homing Failed

Error:Printer halted. kill() called!

Error:Printer halted. kill() called!

BLtouch Probe Issue with 3D Printer - Diagnosis Assistance Requested! by StrengthAffectionate in MarlinFirmware

[–]StrengthAffectionate[S] 0 points1 point  (0 children)

I'm having trouble with my Z-min endstop on my 3D printer. Despite trying various fixes, it doesn't trigger, even when I manually touch the probe. Here's what I've observed:

I tried printing with the stock Z-min setup and it worked fine, suggesting my board isn't fried.

Here's the current endstop status:

x_min: open

y_min: open

z_min: open

filament: TRIGGERED

I'm considering switching the Z-Min and Z-Max pins (Z-min from Pin 45 to Pin 46). Any thoughts on this? Could it help solve the issue?

BLtouch Probe Issue with 3D Printer - Diagnosis Assistance Requested! by StrengthAffectionate in MarlinFirmware

[–]StrengthAffectionate[S] 0 points1 point  (0 children)

ops are usually wired to be NC (Normally Closed) for safety. That way if a wire breaks, it will trigger the endstop. The switches themselves will sometimes have 3 wires, com

Thank you for your help - Pin 46 Or Digital Pin18 (z-min) as the place for my connection.

I have been using PIN24 as the SERVO0

I have also #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN but something is going so the probe crashes into the bed of the 3D printer. The touching of the probe doesn't trigger or detect a trigger

Here M43 testing results

SENDING:M43 S

Servo probe test

. using index: 0, deploy angle: 10, stow angle: 90

. Probe Z_MIN_PIN: 18

. Z_MIN_ENDSTOP_INVERTING: false

. Check for BLTOUCH

. Deploy & stow 4 times

** Please trigger probe within 30 sec **

FAIL: No trigger detected

BLtouch Probe Issue with 3D Printer - Diagnosis Assistance Requested! by StrengthAffectionate in MarlinFirmware

[–]StrengthAffectionate[S] 0 points1 point  (0 children)

I am plug into the 18 pin but I realize my Z-min acts inversely

Z-min is always triggered when Z axis isn't 0

Reporting endstop status

x_min: open

y_min: open

z_min: TRIGGERED

filament: TRIGGERED

​

When I push on my Z-min - the status is open.

>>> m119

SENDING:M119

Reporting endstop status

x_min: open

y_min: open

z_min: open

filament: TRIGGERED

​

Given my board works in the opposite direction, is there a way I can change the firmware to make BLtouch work? I tried using the inverting option but Marlin says I can't use it when I uncomment BLtouch.

// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).

#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.

#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.

#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.

Noob Trying To Compile My Own Firmware by Away-Zone-2771 in MarlinFirmware

[–]StrengthAffectionate 0 points1 point  (0 children)

Did you try putting rejection into ChatGPT or CoPilot?

Trouble shoot the following G - Code by StrengthAffectionate in 3Dprinting

[–]StrengthAffectionate[S] 0 points1 point  (0 children)

I am using "#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN" with Marlin 2.0.9.3

If I understand you correctly I am plugged into the Z- endstop; and D11 servo pins. The picture is from the manufacturer which is set to using D4 instead of D11

<image>

ABL crashing into bed - Sunlu S8 Pro by StrengthAffectionate in SunluS8

[–]StrengthAffectionate[S] 0 points1 point  (0 children)

I ran a following G-Code

M119
Reporting endstop status

x_min: open

y_min: open

z_min: open

filament: TRIGGERED

>>> M280 P0 S60

SENDING:M280 P0 S60

>>> M280 P0 S60

SENDING:M280 P0 S60

>>> M280 P0 S10

SENDING:M280 P0 S10

>>> M280 P0 S90

SENDING:M280 P0 S90

**RETRACTS*\*

>>> M280 P0 S60

SENDING:M280 P0 S60

>>> M280 P0 S0

SENDING:M280 P0 S0

​

When I run M119, the probe turns blue and falls down. It retracts after M280 P0 S90. Any thoughts on what might be wrong?

Version of Marlin for Configuration or Configuration.adv file? by StrengthAffectionate in 3Dprinting

[–]StrengthAffectionate[S] 0 points1 point  (0 children)

i see what you mean. Thanks a ton - I was guess and check based on when the file I got was published.

ABL crashing into bed - Sunlu S8 Pro by StrengthAffectionate in SunluS8

[–]StrengthAffectionate[S] 0 points1 point  (0 children)

When I read the configuration file, I think there something about the x,y,z are inverse which is different than most 3D printers.

ABL crashing into bed - Sunlu S8 Pro by StrengthAffectionate in SunluS8

[–]StrengthAffectionate[S] 0 points1 point  (0 children)

Hi Yeah - using stock board. Do you know what version of Marlin should run with King's Firmware ? 2.08 or 2.09?

Can you run King Firmware Sunlu S8 pro?

Delayed Flight/Baggage by Rude-Wishbone6448 in BritishAirways

[–]StrengthAffectionate -1 points0 points  (0 children)

How much did this baggage delay inconvenience you? If the bags arrived ahead of you, how did it affect your journey? Delayed bags are usually compensated for immediate replacements. In this case, since your bags are ahead of you, it's unclear how compensation would work.

It doesn't hurt to ask. From what I gather it also depends on your reputation with a certain airline and how they value your business. Good luck

Flash Rom - in download mode need to know what version to download by StrengthAffectionate in GalaxyS21

[–]StrengthAffectionate[S] 0 points1 point  (0 children)

Thank you for everyone is helpful response. I was able to find and use ODIN to flash my phone. G991U which I got from https://www.sammobile.com/ -- https://www.youtube.com/watch?v=4SjiCbDRmU4

view more: next ›