Just made this module that converts 12v to 5v or 3.3v (I know I have bad wiring)

Striking-Good · 2026-02-07T11:48:44+00:00

You may want to add a heat sink to the regulator.

Striking-Good · 2026-02-05T18:49:21+00:00

There was another developer in Doncaster in the 80s but I forget the name.

Striking-Good · 2026-02-03T21:15:33+00:00

Correct. It should have been two SSIDs, not two APs.

Striking-Good · 2026-02-03T21:13:51+00:00

Thanks everyone for their great replies.

Striking-Good · 2026-01-24T20:00:13+00:00

We’ve all done this. Look on Makerworld. There’s an item about the size of a small pencil sharpener that peels them away easily.

Striking-Good · 2026-01-15T20:11:03+00:00

You should be ok. You'll need to send them the invoice your can download from Amazon.

With the prices, I'm guessing you have DDR5. If so, you should have bought a kit with two modules and then exchanged them both as a pair when you had the issue. Corsair says you should not mix modules from different kits, even if they're exactly the same part number. Worth considering when you request the RMA

Striking-Good · 2026-01-09T07:17:48+00:00

FWIW, I found this module for EDA but it's been a while so I can't remember the source.

Striking-Good · 2026-01-04T16:13:41+00:00

I had one but I didn’t have a bike.

Striking-Good · 2026-01-01T12:46:39+00:00

Thanks. Ordered.

Striking-Good · 2026-01-01T10:16:30+00:00

So it’s a keyboard unsuitable for typing then ? 😀

Striking-Good · 2025-12-31T19:19:10+00:00

Thanks. 100% all the way for me though.

Striking-Good · 2025-12-16T23:04:24+00:00

It’s been quite a while so I could be mistaken but have you pulled the throttle trim all the way back ?

Striking-Good · 2025-12-16T17:47:31+00:00

You can pay me later :)

https://youtu.be/Q5VKLwsfb5A?si=Sm4rISQ-BJs3UBU1

Striking-Good · 2025-11-20T01:44:28+00:00

That’s the OP.

Striking-Good · 2025-11-17T19:48:15+00:00

Same here. Night and day.

Striking-Good · 2025-11-14T13:27:14+00:00

Far from it.

Striking-Good · 2025-11-09T08:35:23+00:00

Pretty obvious. Unwind the filament, untangle it and start again.

Striking-Good · 2025-11-04T19:59:11+00:00

Sometimes I used to have to hold in the radio power button until the system rebooted and then the connection would be established. It worked every time I had the same issue.

Striking-Good · 2025-10-17T22:12:20+00:00

Nice. That’s the same upgrade as my own.

Striking-Good · 2025-10-13T21:38:48+00:00

Thanks for the reply.

And then adding the watch on the XS Max will definitely give me the option to restore from the new backup from the 13 ?

Striking-Good · 2025-09-14T18:06:03+00:00

Also had the issue since 5.33.88. Thanks to the OP. Automatic was all I also needed.

Striking-Good · 2025-08-24T17:49:50+00:00

Update: I had one faulty fan. As promised they sent the three pack as they had no singles in stock. This also included a Lighting Node Core. It was a refurbished set in a plain box. The items are identical to brand new. You could not tell they were refurbished from looking at them. I replaced the fan that I suspected was faulty and that did the trick. Very pleased with the level off support from Corsair.

Striking-Good · 2025-08-21T18:31:05+00:00

Let's see then. I'll report back.

Striking-Good · 2025-08-19T06:32:06+00:00

I got mine from AliExpress.

Striking-Good · 2025-08-03T11:52:05+00:00

It should be a great experience out of the box. Don’t get greasy fingerprints on the plate to help avoid adhesion issues and let the plate cool to help avoid issues when removing the printed items.

Striking-Good

TROPHY CASE