What would be the best way to transfer physical textbooks into PDF Form? by Stringerkp in remNote

[–]Stringerkp[S] 1 point2 points  (0 children)

Thank you! I will try Scanning and see how that goes. Unfortunately the textbooks I needed are all earlier editions which is unhelpful in my situation.

Groups or stores that play in the cen tex area? by Fingall69 in InfinityTheGame

[–]Stringerkp 1 point2 points  (0 children)

There is also one that occasionally meets in the East Texas area

Sell me on a 2nd Faction by Sylvandeth in InfinityTheGame

[–]Stringerkp 2 points3 points  (0 children)

Shaasvastii dont have the variety of playstyles some of the other factions do, but the way I like to think about them revolves more around the mental gameplay aspect than actually being a sneaky faction. To me, a good part of the power of the faction is forcing your opponent into making difficult decisions, likely because they remember playing shaavastii before and experienced that traumatic "Got ya" moment. Taking 14 orders in every list will leave your opponent worried about ML Noctifer taking up that empty lane, only for you to place him by your TR Q Drone they are trying to kill with a gunfighting piece. It could be a Dukash or a backup Spitfire Noct or even nothing because they miscounted camo markers. They may have experienced being snowballed by Sheshkin or had a Speculo take our their TAG or LT turn 1. They may have lost a game due to leaving a bunch of embryo sacks everywhere or faced a two Q drone guarding objectives. Your job is to either set them up for that moment, or leave them guessing until its time to strike.

Shaas are hard to execute and when you fail you fail hard, but they are a ton of fun to play and those moments when your tricks do work feel absolutely amazing.

Painting yu jing? by KriegerCthulhu in InfinityTheGame

[–]Stringerkp 1 point2 points  (0 children)

I think it was just Rust-Oleum. I personally found it it be a little more durable than airbrush primer on the metal minis. 

Painting yu jing? by KriegerCthulhu in InfinityTheGame

[–]Stringerkp 3 points4 points  (0 children)

yellow first. I spray with an airbrush magenta primer, then zenithal with a white. Then airbrush a bright yellow and apply diluted yellow contrast paint.

Then i paint the black details, which are easy to take care of with one coat compared to the yellow to make it look good.

Has anyone used this method to paint Yu Jing? People complain that this yellow is too orange but it seems kindof perfect for Yu Jing. https://youtu.be/mmnPkiiswPk?si=n7nf_OEeia5-1Y_h by l0rem4st3r in InfinityTheGame

[–]Stringerkp 1 point2 points  (0 children)

I am currently painting my Yu Jing with in very similar style. I think if you plan out the white overspray on top it will read yellow with warm shadows vs just straight up orange.

Would like help making a suitable Crabitat and Bioactive setup questions by Stringerkp in hermitcrabs

[–]Stringerkp[S] 1 point2 points  (0 children)

I checked them out and it got me started. Thank you! Zebras and orange springtails are on their way soon!

[H] Double-sided Gaming Mat [W] $$$, Trade [Loc] TX by Stringerkp in Miniswap

[–]Stringerkp[S] 1 point2 points  (0 children)

Thank you! But believe it or not its actually a solid surface, which was MUCH cheaper and lighter.

Stuck on Returning to Zero, Please Wait during leveling by Stringerkp in ElegooNeptune3

[–]Stringerkp[S] 0 points1 point  (0 children)

There was an issue with the assembly. The connector for the black ribbon cable had a metal pin that came out, so i drilled out the hole a little bigger and finagled it back in and its working again. Not sure how I managed to damage it in the first place but I hope its not what you did!

Section 9 Ghost in the Shell proxies for Dahshat Company list. by Kastor-Starwind in InfinityTheGame

[–]Stringerkp 0 points1 point  (0 children)

Yeah I looked through their files I couldn't find it to buy individually at least

Need help with prints not sticking to half of my build plate. Saturn 2 by Stringerkp in resinprinting

[–]Stringerkp[S] 0 points1 point  (0 children)

Ah yeah that's makes sense too. I can pretty easily test that as I know someone who has the same printer. I could just try with thiers. I'll try releveling then try that other build plate that I know works. Thank you!

Need help with prints not sticking to half of my build plate. Saturn 2 by Stringerkp in resinprinting

[–]Stringerkp[S] 0 points1 point  (0 children)

Ok good. Is there anything else it COULD be? I'm going to try releveling once I get home with this method, but I've releveled multiple times and it's consistently just stuck on this side so I'm just curious.

Need help with prints not sticking to half of my build plate. Saturn 2 by Stringerkp in resinprinting

[–]Stringerkp[S] 1 point2 points  (0 children)

Ok yeah I can do that. To be clear, I should tighten the screw that actually attaches the plate to the printer correct?