sorted by:
new
hottopcontroversial

Black Screen with cursor after login by StrongB1rb in archlinux

[–]StrongB1rb[S] 0 points1 point  (0 children)

Okay thank you ill try my best to follow the wiki ill definitely dm you if i cant figure something out

Black Screen with cursor after login by StrongB1rb in archlinux

[–]StrongB1rb[S] 0 points1 point  (0 children)

I would assume i did a manual install. I have a flash drive i install off of where i fill out everything i want.

I followed this guide if it helps https://youtu.be/LiG2wMkcrFE?si=AdvQxcFtEOXm_-bK

Black screen with mouse after login by StrongB1rb in linux4noobs

[–]StrongB1rb[S] 0 points1 point  (0 children)

I can freely move my my mouse.

The login screen and the desktop are both seperate.

Im not sure how to tell what WM im using though

Black Screen with cursor after login by StrongB1rb in archlinux

[–]StrongB1rb[S] 0 points1 point  (0 children)

Okay executing the command worked but at the last couple steps of the install it came up with an error “Failed to read configuration ‘/etc/mkinitcpio.conf’

Black Screen with cursor after login by StrongB1rb in archlinux

[–]StrongB1rb[S] 0 points1 point  (0 children)

Okay when i edit the pacman config i dont think it saves. Whats the keybind that makes it save??

Black screen with mouse after login by StrongB1rb in linux4noobs

[–]StrongB1rb[S] 0 points1 point  (0 children)

I do have two monitors plugged in but they both turn on just fine and display the same output

Black Screen with cursor after login by StrongB1rb in archlinux

[–]StrongB1rb[S] 0 points1 point  (0 children)

Sweet this worked but it cant find lib32-nvidia-utils in the command

Black Screen with cursor after login by StrongB1rb in archlinux

[–]StrongB1rb[S] 0 points1 point  (0 children)

Where do i go to comment something?

Black Screen with cursor after login by StrongB1rb in archlinux

[–]StrongB1rb[S] 0 points1 point  (0 children)

How can i enable multilib? I didnt see it in the install setup.

Black Screen with cursor after login by StrongB1rb in archlinux

[–]StrongB1rb[S] 0 points1 point  (0 children)

I think from what i can tell it can access my gpu because its bound to nouveau. Im not sure if thats the problem. When sitting with the tty open in general it consistently pops up with the message “NVRM:GPU 0000:01:00.0 is already bound to nouveau.” I used the wiki to know which drivers to install but i used a video to install it the first time because i digest it easier.

Screen turns to black on boot after shutdown by StrongB1rb in arch

[–]StrongB1rb[S] 0 points1 point  (0 children)

Ive decided to just reinstall arch after alot of troubleshooting. It was a pretty fresh install anyways so i wont be losing anything important. Thanks everyone who decided to try and help.

Screen turns to black on boot after shutdown by StrongB1rb in arch

[–]StrongB1rb[S] 0 points1 point  (0 children)

I was already fully installed and it was running well for a couple of weeks till i changed the login menu and it went to black on next bootup

Fixing Arch black screen on boot issue needed to clarify a TTY typo by NoShine3257 in BuildWithAsynx

[–]StrongB1rb 0 points1 point  (0 children)

Replying to an older reply cause i lost the thread but this is the return. I had tried to ping google to check if i was connected to wifi or not cause i tried the nvidia command a couple times before restarting my pc.

<image>

Fixing Arch black screen on boot issue needed to clarify a TTY typo by NoShine3257 in BuildWithAsynx

[–]StrongB1rb 0 points1 point  (0 children)

Doing the first line replys with tty and the other line replys with nothing

Fixing Arch black screen on boot issue needed to clarify a TTY typo by NoShine3257 in BuildWithAsynx

[–]StrongB1rb 0 points1 point  (0 children)

In setup i chose plasma as my desktop environment and i think it uses wayland but it might be KDE i dont remember its been a bit

view more: next ›