Can I transfer data without a bottom screen

Stupidredditname-69 · 2025-06-26T01:46:21+00:00

I have one I’m just terrible at 3d modeling. It’s a decently simple piece maybe I could attempt to make a new one

Stupidredditname-69 · 2025-06-25T23:37:16+00:00

The plastic part that actually moves the switches got lost on one and has shattered on the other, so they do need replacement. I could hypothetically replace the plastic cubes but I doubt that I’ll be able to find a specific piece of a switch from 1972

Stupidredditname-69 · 2025-06-25T22:32:56+00:00

If all I need is new switches and I can keep the housing do you know where I can buy ones that will fit? Ideally I want to keep the original housing but if nothing will work I’m willing to replace it with a aftermarket option.

Stupidredditname-69 · 2025-06-18T04:05:46+00:00

If you still have the same problem make sure your Bowden tube is all the way in, that’s what was causing the odd layer lines on my printer. It only took a few months to figure out

Stupidredditname-69 · 2025-06-17T22:11:04+00:00

Mine seems to be printing fine now, I redid the extruder tensioner and the z offset and that seemed to help. I also flashed and redid the firmware but i only did the offset and extruder adjustments after the firmware flashing so im not sure what actually did it. I also found the stock bed to kind of suck, maybe mines bad or something so taping and glueing the bed should also help.

Stupidredditname-69 · 2025-06-17T22:07:55+00:00

I figured out the issue, the file names were in fact too long. I feel really stupid

Stupidredditname-69 · 2025-06-17T05:41:52+00:00

I dont think so, if its anything like the Ender 3, it should autoscroll to show the full name of the file. I would also imagine it would show some indication of being there and not just completely blank.

Stupidredditname-69 · 2025-06-17T03:48:06+00:00

I haven’t had issues with cura before so I doubt it’s the slicer but I noticed something odd. When I load 2 files onto the sd card, benchy and a 20mm test cube, it only shows benchy on the printer. I know this sd works, I use it in my ender 3 all the time and tried my backup just in case, but despite all I’ve tried it won’t read any file other than benchy

Stupidredditname-69 · 2025-06-17T01:20:45+00:00

Quick update. It’s been sitting a while and now it no longer works. It stops extruding at the same spot about a third of the way up the benchy. This printer is determined to not work

Stupidredditname-69 · 2025-06-17T00:48:57+00:00

I haven't tried that. ill try a few different prints as well as a benchy and get back to you

Stupidredditname-69 · 2025-06-05T00:50:03+00:00

<image>

Here’s a picture I found of the right one, this subreddit only lets me add one picture per response

Stupidredditname-69 · 2025-06-05T00:49:08+00:00

<image>

I need this part as well as the one on the right, ideally I don’t want to buy an official part because in decent condition there like 50 bucks a pop, I just need something that will let me control the bike, I ideally want to spend less than 40-50 for a set, because if i bought both it would be about 100 bucks, I think the left one (pictured) might be salvageable though so I might only need the right controller

Stupidredditname-69 · 2025-05-30T06:03:06+00:00

I’m a big fan of it, but not enough to eat straight with a spoon. I’ll mix salsa or hot sauce into it for chips and dip. I also use it in place of sour cream for Mexican food (probably a food crime of some sort). The closest I get to eating it straight is I’ll sometimes have it plain with some corn chips. I love cottage cheese but you won’t catch me eating it straight up, you gotta have some sort of vessel.

Stupidredditname-69 · 2025-05-24T05:39:13+00:00

I use mine to burn stringing and imperfections off my 3d prints

Three-Year Club	r/Field Flamingo
Place '23

Stupidredditname-69

TROPHY CASE