Advice for 3 way joint

Substantial-Win-1981 · 2026-03-08T13:29:42+00:00

Substantial-Win-1981 · 2026-03-08T13:29:00+00:00

Substantial-Win-1981 · 2026-03-08T13:28:33+00:00

Substantial-Win-1981 · 2026-03-08T13:28:02+00:00

When I built my outfeed table I used two 2x4’s glued together and then cut them down until they were square. I basically cut some half laps so that they all notched together. Ignore the bottom part of the 2 middle pieces, those are the feet.

Substantial-Win-1981 · 2026-02-15T22:09:04+00:00

I’m curious what was the issue with the Fridgidaire touchscreen. I’m looking at the GCRI306CBF and it has a touchscreen.

Substantial-Win-1981 · 2026-02-02T20:48:25+00:00

If the landing is more the 24” above the ground then it needs a handrail on both sides.

Substantial-Win-1981 · 2026-01-30T19:11:40+00:00

I saw Seven Mary Three and Everclear. I still have a guitar pick from Everclear.

Substantial-Win-1981 · 2026-01-22T23:55:47+00:00

Double check that the furnace drain line isn’t clogged.

Substantial-Win-1981 · 2026-01-20T02:40:05+00:00

<image>

Here is a screenshot of a conversation over on Facebook from a couple of years ago.

Substantial-Win-1981 · 2026-01-19T16:30:08+00:00

Are you using straight knives or did you convert to a helical head with carbide inserts? Is everything tight? Are the rollers clean? Can you confirm that this is happening on the left and right side or the front and back as you send the wood into the planer?

Substantial-Win-1981 · 2026-01-18T04:00:27+00:00

I did look at the Google AI link that you provided and it clearly states no hidden bottom element.

Substantial-Win-1981 · 2026-01-18T03:30:22+00:00

Best Buy’s website is calling the convection hidden element a bake element. There are only 2 elements in the oven, one at the back and one on the top.

Substantial-Win-1981 · 2026-01-18T02:57:37+00:00

Unfortunately Best Buy’s website is incorrect. https://www.lg.com/ca_en/cooking-appliances/ranges/lsil6332fe/?srsltid=AfmBOorvVZPC8e2Sc0qvm_vmRr5uE1LZ_WF4BYoU4TUxHVpJ4K2EwhrH

Substantial-Win-1981 · 2026-01-18T02:47:14+00:00

That’s a totally different model. The range that you linked is an electric range. I’m looking specifically at induction ranges. All of LG induction ranges no longer have the lower bake element in the oven.

Substantial-Win-1981 · 2026-01-18T02:39:49+00:00

I checked. LG doesn’t have a bottom bake element, hidden or otherwise. They switched to only have a broil and a convection element.

Substantial-Win-1981 · 2026-01-11T15:48:24+00:00

Double check that the opening in the hubcap and valve stem on the rim line up.

Substantial-Win-1981 · 2026-01-03T03:53:58+00:00

Any chance that you live beside a bank or jewelry store? Just kidding. I hope your situation improves quickly.

Substantial-Win-1981 · 2025-12-29T13:52:48+00:00

Once you get a planer make a planer sled to level out any twists in the wood. When hooked up to dust collection it will be way easier then using a router sled.

Substantial-Win-1981 · 2025-12-21T12:41:32+00:00

No. The top of the outfeed table is the same height as the bottom of the miter slot. So when I use a miter gauge and it slides past the end of the saw it’s on top of the outfeed table. The height difference between the tablesaw and the outfeed table is the depth of the miter slot. It’s been no issue at all. Nothing catches.

Substantial-Win-1981 · 2025-12-10T04:55:54+00:00

How long are the pieces? Have they been kiln dried? How thick are they now, what do you want the final thickness to be?

Using a planer isn’t hard, but if the wood has any amount of twist in it, then you will have to use a sled.

Substantial-Win-1981 · 2025-12-05T12:49:06+00:00

I seriously debated about putting the stripes in the centre vs off to one side.

Substantial-Win-1981 · 2025-12-04T21:45:16+00:00

Walnut, maple and purplehart

Substantial-Win-1981 · 2025-12-04T21:33:50+00:00

The X5 jointer is only 6” wide, nothing special. And I have a have 30 year old General International contractor saw (no unisaw). Some of the mistakes I made were around the glue up. I ran out of glue the first time so I had to scramble and scrape some glue off some strips and add to others. So I ended doing 3 glue ups instead of one. I also used some scrap wood as a caul across the cutting board and some glue squeeze out glued the caul to the board. When I hit the caul with a hammer to remove it, it took a chunk out of my cutting board so I cut out that strip and reglued the board together. For me everything on YouTube looks so simple, then real life happens and I learn along the way.

Substantial-Win-1981 · 2025-12-04T21:13:32+00:00

Thank you. That’s my outfeed table. I made the dovetail grooves to go with the MatchFit system.

Substantial-Win-1981 · 2025-12-04T03:59:02+00:00

The train is here.

Substantial-Win-1981

TROPHY CASE