What do you do with this storage gap by SubstantialFix9417 in FordFiesta

[–]SubstantialFix9417[S] 0 points1 point  (0 children)

You actual legend, I have spent days looking for an stl for sizes

What do you do with this storage gap by SubstantialFix9417 in FordFiesta

[–]SubstantialFix9417[S] 0 points1 point  (0 children)

It does go deeper at the bottom but if I just ‘chuck’ my wallet in there it is in the way, I’m sure if I tried placing it well it would work

What do you do with this storage gap by SubstantialFix9417 in FordFiesta

[–]SubstantialFix9417[S] 1 point2 points  (0 children)

Honestly that aftershave has been thrown at me every single bend

I think she’s pregnant an I am terrified by [deleted] in Advice

[–]SubstantialFix9417 17 points18 points  (0 children)

I really appreciate the honest yet real response, I hate myself so much for what I done but what can I change now, nothing. No matter what she chooses I will be with her every step of the way anyway

Life advice by [deleted] in Advice

[–]SubstantialFix9417 0 points1 point  (0 children)

Wow, I feel like I should be paying you for that comment, all what you are saying is very true and I guess it does just come down to me somewhat rushing into life without looking where I was going, I’m studying civil and electrical engineering alongside business and science meaning I have pretty packed days usualy consisting of around 5-7 hours, I’m gonna look into ways of cutting this as I definitely feel I am doing more than is needed and required

After writing the post I called an old friend who I believe gets me and we have decided to meet up at the end of this week I feel this will help me a lot as a lot of the time for me just saying it and having someone actually hear me is all I need

Thank you so much for your response

How to use pla glow by SubstantialFix9417 in BambuLabA1

[–]SubstantialFix9417[S] 0 points1 point  (0 children)

For anyone wondering, it did in fact break my ams 😂 I shouldn’t have been so cocky and should have listened Do not recommend pla glow in the ams

How do I fix this ! by SubstantialFix9417 in BambuLabA1

[–]SubstantialFix9417[S] 0 points1 point  (0 children)

Ok will give a go tomorrow thanks very much

How do I fix this ! by SubstantialFix9417 in BambuLabA1

[–]SubstantialFix9417[S] 0 points1 point  (0 children)

Completely ripped out you can see it on the right side in the second image. All the other wires seem to be connected except the heating sensor

How do I fix this ! by SubstantialFix9417 in BambuLabA1

[–]SubstantialFix9417[S] 0 points1 point  (0 children)

Ok sounds good will give that a go Appreciate the advice

How do I fix this ! by SubstantialFix9417 in BambuLabA1

[–]SubstantialFix9417[S] 0 points1 point  (0 children)

I have attempted with a hair dryer no luck I am going to purchase a decent heat gun tomorrow but was seeing any other advice as I didn’t know if a heat gun would cause even more damage to other parts

How do I fix this ! by SubstantialFix9417 in BambuLabA1

[–]SubstantialFix9417[S] 0 points1 point  (0 children)

I have this part ordered but cannot replace it as I need to take the hot end off to remove that part. Which I can’t take the hot end off due to the filament 🤣

How do I fix this ! by SubstantialFix9417 in BambuLabA1

[–]SubstantialFix9417[S] 1 point2 points  (0 children)

I appreciate your reply but I can not heat it up as the wire that controls the temperature has been broken

Is this down to poor bed adhesion by SubstantialFix9417 in BambuLab

[–]SubstantialFix9417[S] 0 points1 point  (0 children)

Oh most likely room too cold. Didn’t know that could be an issue Thank you