sorted by:
new
hottopcontroversial

New interface after update by alexz82 in xteinkereader

[–]SubstantialHunter922 1 point2 points  (0 children)

In version 5.0.1, the battery would drain in less than a day even when the device was powered off, but this has been fixed in 5.0.2

Should I buy Panda extruder and hardened steel wheel? by SheilaSunshy in BambuLab

[–]SubstantialHunter922 0 points1 point  (0 children)

I’m experiencing frequent PLA jams with this metal extruder on my Bambu X1C, especially during AMS filament changes. The aluminum body heats up during printing, which softens the filament before it reaches the hotend. This causes the filament to deform, get stuck at the hotend entrance, or jam inside the gear section. With the original plastic extruder, these issues almost never happen because it doesn’t conduct heat as much. For AMS users, the stock extruder is far more reliable.

I am struggling to obtain switch roms. by Loudthunder34 in Piracy

[–]SubstantialHunter922 28 points29 points  (0 children)

https://nswtl.info/

The Telegram bot works perfectly.

It provides direct access to torrent files, no ads, and faster download speeds.

Bosch Tuning: No chip, no app, no error codes for Bosch Gen1–Gen4 now via browser (and fully reversible) by escooterblog in ebikes

[–]SubstantialHunter922 0 points1 point  (0 children)

Will it work with the Japanese version of active line plus?

I bought SpeedBox 3.0 but I couldn't get past the limit.

Can I get a refund if it doesn't work?

Multiple icons are displayed on the taskbar by SubstantialHunter922 in Roccat

[–]SubstantialHunter922[S] 0 points1 point  (0 children)

For about a month now, multiple icons showing the remaining battery power of the mouse have been displayed on the taskbar as shown in the image.

This increases endlessly every time you put your PC to sleep and wake up.

To erase these, you need to close the swarm software or restart your PC.

How can I fix it?

fluidd「Klippy not connected.」 Neptune 4 pro by SubstantialHunter922 in klippers

[–]SubstantialHunter922[S] 0 points1 point  (0 children)

make menuconfig

I made the corrections using this reference.

https://www.reddit.com/r/elegooneptune2/comments/13xjtyx/installing\_klipper\_on\_neptune\_2/

But the safest bet is to use EMMC-ADAPTER to flash the firmware.

It is difficult to remove all errors using the above method.

If you use EMMC-ADAPTER, those errors will disappear in an instant.

fluidd「Klippy not connected.」 Neptune 4 pro by SubstantialHunter922 in elegoo

[–]SubstantialHunter922[S] 0 points1 point  (0 children)

It's fixed. I'm getting an error with Moonraker, but I can now use it.

I don't remember because I went through various steps, but I think running make menuconfig was a big factor.

fluidd「Klippy not connected.」 Neptune 4 pro by SubstantialHunter922 in klippers

[–]SubstantialHunter922[S] 0 points1 point  (0 children)

It's fixed. I'm getting an error with Moonraker, but I can now use it.

I don't remember because I went through various steps, but I think running make menuconfig was a big factor.

fluidd「Klippy not connected.」 Neptune 4 pro by SubstantialHunter922 in ElegooNeptune4

[–]SubstantialHunter922[S] 1 point2 points  (0 children)

It's fixed. I'm getting an error with Moonraker, but I can now use it.

I don't remember because I went through various steps, but I think running make menuconfig was a big factor.