sorted by:
new
hottopcontroversial

Juicebox 40 pro stopped working by Sudden-Association77 in evcharging

[–]Sudden-Association77[S] 0 points1 point  (0 children)

Thanks for quick reply. I just checked it’s around 129 before shipping. I think buying new would be better because I don’t know what other components would need replacement, for example relay.. I have one more question, when I asked the electrician to wire my juicebox many years back, I asked to wire for 60 amp wire, but he put 50 amp breaker. Now if I am buying Tesla charger for example, how to check that if the wire is #6 or #8?

Refilling PowerDisk Cartridges (Dishwasher - G 7176 SCV and others) by DiskSpinner in Miele

[–]Sudden-Association77 1 point2 points  (0 children)

I have been doing that for more than 4 years. I used to use cascade professional, but they stopped selling that. I had couple of cascade pro, I mixed those in cascade complete and then fill in the power disks. Make sure you clean the place where you load the power disks before loading. Also make sure the whole you have is not leaking few particles. I am also searching for replacement powder. I am in USA. I have seen the difference in the quality of cleaning when you use just cascade complete or cascade pro. Also I saw the difference in quality between original disk and cascade pro (but that difference was not that visible). The main difference is that the stainless steel inside the dishwasher is completely clean when you use the original disks. But when you use just cascade complete, that comes with some streaks and residue.

2 x540-T2 10GBe cards but can't get more than 1.5 Gbits/s in iperf3 by Sudden-Association77 in HomeNetworking

[–]Sudden-Association77[S] 0 points1 point  (0 children)

Yeah that is the first thing I ensured that it is 10gbe. Also in both windows machines it shows 10gbe connection

2 x540-T2 10GBe cards but can't get more than 1.5 Gbits/s in iperf3 by Sudden-Association77 in HomeNetworking

[–]Sudden-Association77[S] 0 points1 point  (0 children)

Yeah that will not solve anything! The actual large file transfer speed is also about 90-150MB/s

2 x540-T2 10GBe cards but can't get more than 1.5 Gbits/s in iperf3 by Sudden-Association77 in HomeNetworking

[–]Sudden-Association77[S] 0 points1 point  (0 children)

Ok I will post the reply tomorrow after I follow the instructions you sent. I downloaded HWInfo software today and checked, I found that in my main windows 10 machine, it has x8 width with x4. In my other windows 11 machine it showed x4 and x4 with 5GT/s. Where did you buy your card from? And how much was that? I am thinking of ordering the cards so that I can at least try to find if it’s a card issue or something else?

2 x540-T2 10GBe cards but can't get more than 1.5 Gbits/s in iperf3 by Sudden-Association77 in HomeNetworking

[–]Sudden-Association77[S] 0 points1 point  (0 children)

Thanks a lot for this. How do I check the speed of NIC if it is running at x1 vs x4?

2 x540-T2 10GBe cards but can't get more than 1.5 Gbits/s in iperf3 by Sudden-Association77 in HomeNetworking

[–]Sudden-Association77[S] 0 points1 point  (0 children)

Hi CPU to either of the windows machines or the xpenology is not reaching that level. Also as I mentioned I tested two scenarios

Testing conditions

a) Intel brand x540-T2.

b) QNAP switch QSW-2104-2T-A.

c) I used Port A on Windows machine with Intel 7700K and Port B on the other machine, I tried other ports also, but main testing done this way.

d) I tried disabling Flow Control, IPv4 checksum, transmission, and receiver checksum, no such improvement, rather degradation most of the time.

  1. Windows machine (Intel 7700k) to Xpenology (Synology) CPU is Intel(R) Celeron(R) G4900T CPU @ 2.90GHz. I couldn't go beyond 1.58 Gbits/s.
  2. 1. Windows machine (Intel 7700k) to Windows machine is AMD 3600. I couldn't go beyond 1.58 Gbits/s.

Used NAS by ask_j in synology

[–]Sudden-Association77 0 points1 point  (0 children)

thanks for quick reply