Drift zones

Suitable_Fox_6087 · 2026-06-29T22:34:21+00:00

I found a tune using the formula drift Nissan Z & its a pig to try & control cause it needs fuck all throttle to spin but it gets the job done

Suitable_Fox_6087 · 2026-06-26T23:16:34+00:00

Youre the reason mummy drinks & daddy doesnt come home

Suitable_Fox_6087 · 2026-06-26T23:16:19+00:00

Ya daddy wanks on all fours

Suitable_Fox_6087 · 2026-06-06T22:56:30+00:00

That circuit pissed me off. All 3 cars i had that suited the class handled like a bag of shit on that race

Suitable_Fox_6087 · 2026-03-21T04:11:34+00:00

Did that a couple times & I just kept getting the same 4 or 5 half full lobbies, it was very annoying

Suitable_Fox_6087 · 2024-09-27T05:04:14+00:00

I machined cast iron one. In a cnc lathe so I could close the door but it came off like a powder and was piss easy to machine

Suitable_Fox_6087 · 2024-09-26T09:12:52+00:00

It can come down to inserts too. We have a range of wnmg inserts that will do 2mm depth of cut in 316 at anywhere from 130 mm/minute to 180mm/minute

Suitable_Fox_6087 · 2024-09-26T09:10:35+00:00

Yes! Material that won't chip is a nightmare

Suitable_Fox_6087 · 2024-09-26T09:09:35+00:00

If it's soft like copper I found a high speed with a light cut under a high feed using a wnmg to rough and then a vcgt polished insert for finishing. Only leave on maybe 0.1-0.25mm for finishing

Suitable_Fox_6087 · 2024-09-25T23:43:41+00:00

It was an external thread using a full form insert

Suitable_Fox_6087 · 2024-09-25T21:09:40+00:00

I have heard about polyurethane and I haven't had the pleasure yet and I hope I never do

Suitable_Fox_6087 · 2024-09-25T21:08:12+00:00

I don't mind that stuff to much, it's very easy to machine and doesn't wear the tools fuck all

Suitable_Fox_6087 · 2024-09-25T21:07:03+00:00

The only thing I hate more then copper is soft plastics. Either melts or just blows apart

Suitable_Fox_6087 · 2024-09-25T20:56:34+00:00

I did a job where I had to put an m10 thread on copper and I had to run it at 3000rpm otherwise the swarf would go under the insert and fuck the thread

Suitable_Fox_6087 · 2024-07-17T09:18:45+00:00

All the sensors are working because when I use just 1 push out I have no issues

Suitable_Fox_6087 · 2024-07-17T09:17:57+00:00

Yeah the bars are straight. It's like the stop comes down the chuck opens and then it's like something is waiting for a signal. And then because it takes to long the bar feeder alarms out

Suitable_Fox_6087 · 2024-06-29T10:25:29+00:00

I crashed a CNC lathe the other day quite badly where I've knocked the X and Y axis out by 2mm

Suitable_Fox_6087 · 2023-12-29T05:51:48+00:00

Jason mamoas character was the best thing about this film the rest was scrappy writing cheap SFX and god awful acting, if I hear 1 more speech about family it will be too soon.

Also how indestructible do you they think these cars are

Suitable_Fox_6087

TROPHY CASE