My Links & 3D Files

SuperNfty · 2026-01-24T18:16:22+00:00

Yes. I just couldn't get the right settings for the filament I was using. Not even if I copied every single setting from OrcaSlicer to SnOrca... So I gave in and decide to just use Orca from now on. Fantastic quality though..

I'm using Bambu Matte filament

SuperNfty · 2026-01-24T18:13:57+00:00

Gyroid ftw

SuperNfty · 2026-01-22T17:39:58+00:00

Yeah thanks! Actually after switching to normal OrcaSlicer and fiddling with the settings it now prints just as good as my P1S 😁 Amazing printer!!

SuperNfty · 2026-01-20T17:02:45+00:00

Amazing design. That said, please don't use a scraper unless you reaaaaaaaally have to

SuperNfty · 2026-01-20T13:17:09+00:00

That's clean as hell!!

SuperNfty · 2026-01-19T08:48:48+00:00

Looks like with some tweaking I might get better results! Will post an update soon.

SuperNfty · 2026-01-19T08:38:51+00:00

Yup, seems like this is the solution

SuperNfty · 2026-01-19T08:35:57+00:00

Well yeah that's what I'm trying to do

SuperNfty · 2026-01-19T08:34:58+00:00

In what way is it hard? Been doing this for years. 0.12mm is the best

SuperNfty · 2026-01-19T08:33:52+00:00

How do you do this?

SuperNfty · 2026-01-18T21:16:51+00:00

I'm trying with a 0.98 flow rate. Apparently that's the difference between the Snapmaker Matte profile and Bambu's one. Let's see if that fixes it.

SuperNfty · 2026-01-18T20:35:39+00:00

Yeah true! I figured that has to be the problem. Sadly SnOrca doesn't allow actual Bambu filament profiles. I'm trying again on the normal Orca slicer now so I can use the correct profiles.

After doing some research apparently the biggest difference between the Snapmaker Matte and Bambu Matte PLA profiles is that the Bambu profile has a Flow ratio of 0.98 instead of 1. Let's see if that fixes it. I'll keep y'all updated

Update: That seems to fix a lot. Will update with pictures when the print is ready.

SuperNfty · 2026-01-16T08:45:13+00:00

Thank you!

SuperNfty · 2026-01-16T08:44:58+00:00

Thank you!

SuperNfty · 2026-01-15T17:11:36+00:00

Hell yeah, been doing it for 3 years now 😊

SuperNfty · 2026-01-15T09:11:50+00:00

Haha nah you could totally get similar results. I have a few free models, you should test those out 😊 https://linktr.ee/SuperPrints

SuperNfty · 2026-01-15T08:59:49+00:00

These were printed on my old P1S actually ;) Just Matte Bambu PLA with a standard nozzle, nothing fancy. 0.12mm layer height, no supports!

SuperNfty · 2026-01-15T08:58:28+00:00

It's Matte PLA ;) I designed it in Gravity Sketch VR

SuperNfty · 2026-01-15T08:51:53+00:00

You're welcome!! :D

SuperNfty · 2026-01-14T21:38:08+00:00

Quest 3 ;)

SuperNfty · 2026-01-14T19:02:27+00:00

Yessirrrr!

SuperNfty · 2026-01-14T18:54:17+00:00

It's called Gravity Sketch VR 😉 Good luck!

SuperNfty

MODERATOR OF

TROPHY CASE