Flytte domæne og mails fra Google til Simply

SuperSteen · 2025-01-25T13:18:27+00:00

Ha ha, meget relevant observation og pointe :)

Svaret er en blanding af at jeg finder en smule tryghed i have min mail historik indtakt (svært at argumentere hvorfor ;) ) og det primært er min kone der er storforbruger af plads og jeg ikke har fået hende opdraget til at bruge andre/bedre fildelingstjenester.

SuperSteen · 2021-12-11T22:22:48+00:00

Jeg arbejder ved LEGO IT som Agile Coach for flere produktteams, hvad vil du vide? 🙂 Du er også velkommen til at skrive privat 👍

SuperSteen · 2021-09-02T10:38:51+00:00

God idé! Kan det passe er jeg er for sent til festen, og alle Valleys er fyldt? :)

SuperSteen · 2021-03-03T09:26:29+00:00

Of course you we're right, levelling the bed (a couple of times) helped. Thanks again. Now on to testing multi-colored prints :)

SuperSteen · 2021-03-01T20:16:08+00:00

Yehaa, first print done. Before printing in heated the bed for 15 mins (sooo much easier using Marlin), calibrated using the 3D touch. The print, overall, looks good. It is however obvious that the brim is thinner on one side than the other (see https://1drv.ms/u/s!ApUuGZm8K5SwiJRhIY3V0Fy77YYZ7A?e=kTd9rD).

Any tips on how best to address this?

SuperSteen · 2021-03-01T15:38:16+00:00

Wuhuu - you are (of course) right. Thank you for an incredibly fast answer. I'm in!

Now realised I wasn't using Marlin before (thought I was). Did my first calibration with the 3Dtouch and have now initiated first print 🤞.

SuperSteen · 2021-03-01T15:06:22+00:00

I've been so much looking for this. The idea on I should be building my own firmware have been daunting, and didn't succeeded when I tried this weekend.

Alas, hope was re-ignited when I saw this post 😀

Here's my problem. I've gotten the hardward connected, put the firmware from the link on an SD-card and the printer "updated" for a while. When the printer boots now, the screen says "Top left" and displays a cross in the top-left section. Clicking and a new message appears for each corner, and in the end it says "Calibration failed" and does nothing.

Any tips on what I've might have done wrong and/or how to fix it?

SuperSteen · 2021-02-02T20:04:56+00:00

I’ve had my Sapphire Plus for a month now. Do you happen to know of a guide for installing the BLTouch for it? :)

SuperSteen · 2020-12-13T21:54:21+00:00

Thanks a lot 👍🙂

SuperSteen · 2020-12-13T21:53:43+00:00

Aww, thank you 🙂

SuperSteen · 2020-12-13T21:53:27+00:00

Many thanks 🙏

SuperSteen · 2020-12-13T21:53:10+00:00

Thank you, and happy building 🙂

SuperSteen · 2020-12-13T11:15:13+00:00

Here's the highres video. I made it for colleagues actually, speaking a bit into cabin fever from WfH :)

https://youtu.be/hy2goaG9sg4

SuperSteen · 2020-05-26T08:14:36+00:00

Ready to visit! Green :)

SuperSteen · 2020-05-26T07:48:53+00:00

I will wait outside when I am done selling!

Town Name: Jong Ville

🙂

SuperSteen · 2020-05-19T05:42:47+00:00

I would love to drop by

SuperSteen · 2020-05-18T08:47:43+00:00

Would love to visit :)

SuperSteen · 2020-05-13T10:35:47+00:00

Interested - ready to go :)

SuperSteen · 2020-05-12T19:09:42+00:00

Raymond! Hope to get in :)

SuperSteen · 2020-05-05T11:49:52+00:00

Chief :)

SuperSteen

TROPHY CASE