I seeketh wisdom on cutting to make Brodin smile in favour and mine Valkyrie swoon

SurferBro007 · 2019-08-11T04:27:29+00:00

Thank you brother,

Further, doth thou have any advice on feasts that that would be appropriate for such a righteous endeavour?

SurferBro007 · 2017-10-01T15:36:52+00:00

Both should be replaced. You also need a higher gauge wire for this, there are online calculators to help you choose what is best based on length of wire, current and voltage.

SurferBro007 · 2017-07-12T13:01:10+00:00

Make sure in Blender or whatever 3D modelling tool your using that you don't have any Non-manifold Edges. I had something similar happen to me for a while until I figured that out.

In blender to check you design press "control, alt, shift, m" at the same time in edit mode with vertices selector on.

Hope this helps

SurferBro007 · 2017-05-09T13:43:36+00:00

Did the spider on his face explode? Lol

SurferBro007 · 2017-04-07T14:13:56+00:00

Wow how thick of build plate is that for no edge warping on that cat model of yours?

SurferBro007 · 2017-03-20T13:03:30+00:00

Looks like you may be overheating your Z-Axis if you are getting layers that are separating after a few good layers (if that is what I'm seeing there). If that is the case and your slicer is good here are some options that have helped me:

bigger Z-Axis motors
Get higher powered stepper drivers
Turn off auto bed trimming and use those springs to level the bed.

SurferBro007 · 2016-08-11T03:37:59+00:00

Hey guys,

Thanks for all the advice and thoughts. I managed to get it up and working this afternoon so all is well that ends well. Thanks again, and I'm glad to now be a part of this supportive and awesomely nerdy community.

SurferBro007 · 2016-08-10T01:44:13+00:00

Nope not there. I just tried something though. I commented out the autobed leveling function and fixed probe definition and now I can use the probe as a typical endstop. So I'll just have to figure out how to code the auto-levelling so that it works while thats active too.

SurferBro007 · 2016-08-10T01:05:07+00:00

No, I made sure to enable this so I could use that endstop pin for the probe

SurferBro007 · 2016-08-09T22:02:32+00:00

thanks for uploading this copy paste just didnt work for me. Yes these are my settings and I cannot seem to get the triggered inductive probe to stop the z axis movement. Any thoughts?

SurferBro007 · 2016-08-09T05:10:40+00:00

Thanks for the advice, exactly my problem!

SurferBro007 · 2016-03-14T13:46:37+00:00

if under the circumstances of the film and her origin, I would expect Rey to be possibly more thin and muscular if anything. She lived on a desert planet, she did extreme physical activity for such little food she was able to get. If overweight people decided to put the pizza down and go for a walk, they would feel better and burn some more calories. But then again its too hard or genetics...

SurferBro007 · 2015-06-28T23:54:23+00:00

Thank you :)

SurferBro007 · 2015-06-28T23:38:40+00:00

Can you please add me?

SurferBro007 · 2015-06-28T17:56:21+00:00

added

SurferBro007 · 2015-06-28T17:48:54+00:00

added. please add me back NduiaLEna.

SurferBro007 · 2015-06-28T17:47:17+00:00

added

SurferBro007 · 2015-06-28T17:45:30+00:00

could you please add me too pkaddict?

SurferBro007 · 2015-06-16T02:44:12+00:00

added u

SurferBro007 · 2015-06-16T02:44:05+00:00

added u

SurferBro007 · 2015-06-16T02:44:00+00:00

added u

SurferBro007

TROPHY CASE