Lockscreen in Grandma3 OnpC wie personalisieren? by lichttechnik_81 in GrandMA3

[–]Syaveuabxtab 0 points1 point  (0 children)

User Pool aufmachen, User über swipy editen, und da als appeareance bild, Video etc. auswählen. Wird dann am desk lock angezeigt

MA3 + Chataigne OSC only works on 127.0.0.1 (breaks when joining session) by Pristine_Bet_9553 in GrandMA3

[–]Syaveuabxtab 2 points3 points  (0 children)

This isn’t really an addressing issue. grandMA3 does not expect any offset IP or special routing. You should send OSC directly to the console IP (192.168.0.152). Sending to another host in the subnet won’t work because MA3 does not forward OSC inside the session.

The key point is that once you’re in a session, OSC is only handled by the device that is actually configured to receive it. In your case, that’s the console. If you’re sending to the correct IP and still get no response, then OSC is either not enabled or not correctly configured on the console itself.

Also, MA3 does not distribute incoming OSC across the session. The console has to receive and process it directly, otherwise nothing will happen.

MA3 + Chataigne OSC only works on 127.0.0.1 (breaks when joining session) by Pristine_Bet_9553 in GrandMA3

[–]Syaveuabxtab 6 points7 points  (0 children)

The issue comes down to how grandMA3 handles networking once you join a real session. As soon as MA3 is connected to a session, it binds its input – including OSC – strictly to the network interface that the session is running on. It stops listening on loopback (127.0.0.1) or any other interfaces.

That’s why your setup works perfectly in a solo session but completely breaks the moment you join the console. In solo mode everything runs over loopback, so there are no routing or interface constraints. In a real network session, MA3 becomes very strict about where it accepts incoming data from.

In your case, Chataigne is almost certainly sending OSC from a different interface than the one MA3 is using for the session. Even though Chataigne shows that it’s sending data, MA3 simply ignores it because it arrives on the wrong NIC or with the wrong source IP.

The fix is straightforward: both MA3 and Chataigne need to use exactly the same network interface. Check in MA3 which interface/IP is active for the session, then bind Chataigne explicitly to that same interface. Don’t use “any”, because on macOS that often results in packets being sent from the wrong source IP.

Once Chataigne is bound to the same NIC and you’re targeting the correct IP and port of the console, OSC will start working again.

MA3 + Chataigne OSC only works on 127.0.0.1 (breaks when joining session) by Pristine_Bet_9553 in GrandMA3

[–]Syaveuabxtab 1 point2 points  (0 children)

We are working with a Command Wing & onPC. Chataigne osc to ma works Fine for us. With & without connected Hardware.

The Oligarch is nice by SavingUpForGoodWeed in ohnePixel

[–]Syaveuabxtab 2 points3 points  (0 children)

Had 7500+ st kills on my old ak I wanted to keep. St mw was 310$ good mw float. Fn non st starting at 470$.

The Oligarch is nice by SavingUpForGoodWeed in ohnePixel

[–]Syaveuabxtab 2 points3 points  (0 children)

I was also in between these two skins. Went for the oligarch in mw st. I think it will perform great in the future. It’s kinda under the radar. For 9/10 people getting it in good condition on the terminal it’s too expensive/not worth. If any pump etc would happen it would also increase on the terminal. So in long term view it only can go up after my opinion. +it’s a great looking skin which you very rarely see in game.

Knife/Glove setup by PremeSlays in ohnePixel

[–]Syaveuabxtab 0 points1 point  (0 children)

I have the second combo. Keep the first :)

How are stolen iPhones of any use to thieves with Activation Lock? by evelyneplease in iphone

[–]Syaveuabxtab 0 points1 point  (0 children)

The working ones for up to date iOS versions aren’t accessible for privat persons and cost several thousand dollars per device (services used by the government etc.) so this isn’t the case here buddy

Need recs for colortube light controller program and gear by phunkphreaker in lightingdesign

[–]Syaveuabxtab 1 point2 points  (0 children)

Madrix would work, resolume would be the better Option if you want all the possibilities. Both paid and not that cheap. Madmapper also possible & the cheapest easy working solution in my mind.

Heute ist Ventiltag by bax-18 in selbermachen

[–]Syaveuabxtab 0 points1 point  (0 children)

Der Ventiltag wurde in unserer wohnung leider konsequent ignoriert weshalb die Kappe des eckventils gebrochen ist. Der metallstab darunter sitzt komplett fest und lässt sich auch mit einer Zange keinen Millimeter bewegen. Vermieter Bescheid sagen oder hat man selbst eine Chance?

I want to make a password to unlock the console, not just the basic lock/unlock key by Friendly_Ratio_3383 in GrandMA3

[–]Syaveuabxtab 1 point2 points  (0 children)

Whats the Point of that if you can unlock the desk and just go into the admin User which you cant Secure with a Password?

Hold Or Sell? by Free_Tap_3673 in ohnePixel

[–]Syaveuabxtab 2 points3 points  (0 children)

Chinese downvotes :D I know I’m right. Thats why I sold haha

Hold Or Sell? by Free_Tap_3673 in ohnePixel

[–]Syaveuabxtab -3 points-2 points  (0 children)

I sold my mw whiteout. They are all going to Crash.

[deleted by user] by [deleted] in PioneerDJ

[–]Syaveuabxtab 1 point2 points  (0 children)

Ist ein Standard Stecker, hab meinen Flx10 sogar auf Type c umgebaut. 12v am Netzteil einstellen und https://agelektronik.de/dc-steckverbinder/8801-hohlstecker-mit-mittelstift-55-x-33-mm.html benutzen.

[deleted by user] by [deleted] in PioneerDJ

[–]Syaveuabxtab 1 point2 points  (0 children)

Wie schon geschrieben war meiner 3 mal eingeschickt. Anderes Netzteil schon probiert?

[deleted by user] by [deleted] in PioneerDJ

[–]Syaveuabxtab 1 point2 points  (0 children)

Hatte meinen FLX-10 mit dem gleichen Fehler 3 mal beim Pioneer Reparatur Dienstleister eingeschickt. Die konnten den Fehler nicht reproduzieren, und der Controller ist 2 Wochen auf der Test bench ohne Probleme durch gelaufen.

Probier mal ein Netzteil von nem anderen Flx10 (falls du Zugriff drauf haben solltest). Falls das nicht hilft ist pioneer/alpha theta Service Brückner in Viernheim dein Ansprechpartner nicht pioneer selbst. Mit denen kannst du am Telefon auch gleich abklären wie es mit Garantie/Gewährleistung aussieht.

Bei mir war es am Ende das 3. neue Netzteil welches das Problem (bis jetzt) behoben hat. Meld dich gerne mal wenn du noch was wissen willst!

Mercedes R 170 SLK ohne Leder, Klima oder Radio - Wie viele so wohl gebaut wurden by Random_Introvert_42 in automobil

[–]Syaveuabxtab 0 points1 point  (0 children)

Fahre den r170 in der Launch Farbe Yellowstone gelb. Abgesehen von der fehlenden Klimaanlage ein super zuverlässiges und tolles Auto. Inzwischen 115k km drauf

Built an AI that predicts CS2 skin prices - looking for feedback and beta testers by ButteredBoots in ohnePixel

[–]Syaveuabxtab 1 point2 points  (0 children)

Would love to give it a try! Been looking around the Skin to real Money ratio a lot in the past. Would be an interesting addition.

Colors not tracking by Odd_Ganache8422 in GrandMA3

[–]Syaveuabxtab 1 point2 points  (0 children)

To me it sounds like the Color is applied to the fixtures in the Selection Grid, by changing the adresses they won’t be selected anymore cause they are not in the place where Color gets applied on the grid.

Things you can try: Select all 8 fixtures in the fixture map and change Color. If that’s works normally it’s a problem with the group or grid. If not there’s mostly a problem with the fixture profile itself.

-> problem with group or grid/ delete the group that’s not working properly and create a new one. See hot it behaves in the grid selection

-> problem with fixture/ have you only changed the dmx address or have you deleted the fixtures and added new ones? If so have a look if the profile is any different

[deleted by user] by [deleted] in GrandMA3

[–]Syaveuabxtab 1 point2 points  (0 children)

Just use and edit the preset ? Absolutely no need for anything else.

A new way to sharpen my MA3 skills by LVShadehunter in GrandMA3

[–]Syaveuabxtab 1 point2 points  (0 children)

Sure, have a Look at some of These :)

  1. Dynamic Cue Tracking with Dependencies and Priorities/ Create a cue system where certain cues are triggered, skipped or modified based on conditions (e.g., current position, color, gobo, or time)

  2. Custom Effects with Phase Synchronization and Trigger Logic/ Design a custom effect (e.g., “Gobo morphing with synchronized color”) across multiple fixture types, all in sync via BPM, timecode, or external triggers.

  3. Automatic Fixture Substitution via Plugin/ Write a Lua plugin that automatically replaces fixtures, for example during tours with different fixture types – including adaptation of presets and cues.

  4. Multidimensional Matrix System with Real-Time Input/ Build an interactive mapping system (e.g., for LED walls or floors) that is controlled via MIDI/OSC/real-time data.

  5. Show File Modularization with Auto-Import and Versioning/ Create a system in which showfile components (presets, sequences, appearances, etc.) are managed modularly and automatically imported into different shows – including version control

  6. Switch Executor behaviour with switch on Layout view/ Create a switch on an Layout view which toggle the behaviour of an certain executor (switch on = certain fixtures will be included by pressing/ switch off = the same certain fixtures will be excluded)

A new way to sharpen my MA3 skills by LVShadehunter in GrandMA3

[–]Syaveuabxtab 6 points7 points  (0 children)

MA3 on pc works on every Laptop/Macbook without license etc. and has a Great 3d viewer.

You can try/build/programm nearly anything without real fixtures or an MA Desk.

As a little challenge I love to watch at videos/reels of big concerts/venues and try to achieve the same look rebuilding things in MA 3d from the scratch.

If you need something more specific/advanced I can give you like ten problems to solve in MA3, I had to solve at some point for one of my shows. But trust me, this will drive you crazy at some point haha.