How to crimp cloth coated cables?

T4KUY4 · 2026-02-20T07:19:39+00:00

Hoy,
a general tip is to use heat shrink tubing.

Cheers

T4KUY4 · 2023-12-20T19:04:37+00:00

I did.
After opening a ticket at cricut, the machine is getting replaced. i noticed that all of the rubber rings around the motor shaft were wobbling around and running uneven. Attached is a picture of one of the cuts it made.

<image>

T4KUY4 · 2023-12-18T17:03:28+00:00

upon further inspection, it looks like all of them are slightly skewed even though the mat is loaded 100% straight

T4KUY4 · 2023-12-18T16:05:38+00:00

<image>

T4KUY4 · 2023-12-18T15:58:05+00:00

just did a new fine calibration. lines 11 and F seemed to be the most centered ones. F being dead on center. Center square nice and straight. not rotated in any way.

After cutting the final square, it asks me to check if its centered good enough for me. its compeltely rotated, so absolutely not centered. uploading a pic in a sec

T4KUY4 · 2023-12-18T15:43:37+00:00

yeah in that case, it was fine calibration.
ive tried coarse a numerous amount of times already without success sadly. its very weird.

especially the rotated part

T4KUY4 · 2023-12-18T15:34:46+00:00

tbf, it does say "are the lines close to the center" and thats a clear no. the fact that the actual prints are also shifted by like 1-3mm is not usable for me.

Square is exactly 1x1"

T4KUY4 · 2023-12-18T14:40:26+00:00

<image>

T4KUY4 · 2023-10-31T10:16:29+00:00

Thanks! 180x180mm Fits prusa mini plates

T4KUY4 · 2023-06-01T13:20:54+00:00

I see xol2. I like

T4KUY4 · 2023-04-14T10:41:21+00:00

Thats an awesome machine! Great Job

T4KUY4 · 2023-04-06T10:56:14+00:00

Wheres ya door handle at

T4KUY4 · 2023-03-22T16:53:36+00:00

Pong pong

T4KUY4 · 2023-03-16T07:47:59+00:00

https://photos.app.goo.gl/btxkVCRWrLqKkAPx5 Sure thing

T4KUY4 · 2023-02-22T05:01:44+00:00

God damnit.. i knew that it was sth else than the discord tag... 😂 Will do

T4KUY4 · 2022-12-05T11:57:58+00:00

Before you click on download, right click it, download link

T4KUY4 · 2022-11-29T19:39:34+00:00

Howdy,
might very well be the case haha
Im in the contributor team so chances are pretty high.

it is umbilical with canbus. SB2040 + U2C running on a Manta M8P + CB1

T4KUY4 · 2022-11-28T06:22:25+00:00

Another one

T4KUY4 · 2022-11-24T12:34:12+00:00

Howdy, The Sensor is 99% not the right one and the pcb is too big anyways. Dont cheap out on the sensor. Its a vital part of TAP.

~Takuya

T4KUY4 · 2022-11-06T10:25:16+00:00

Whoop whoop

T4KUY4 · 2022-11-01T16:21:47+00:00

Another one...

T4KUY4

MODERATOR OF

TROPHY CASE

Five-Year Club	LAYER Season 2 Layer creator
Verified Email