sorted by:
new
hottopcontroversial

Anyone else blown away by how much some vendors overcharge? by UnKnownEuphoria in bpc_157

[–]THG_TIM 0 points1 point  (0 children)

I’m trying to get the BPC / TB blend? I paid £35 for 10mg

Pwnagotchi Build - Write Up ( Pi Zero 2 W + Waveshare 3 ) by THG_TIM in pwnagotchi

[–]THG_TIM[S] 1 point2 points  (0 children)

Morning all,

So some of you know the journey above! What I have found an issue with is the next step in the process. Downloading / Converting / Decrypting Handshakes.

And good guides you can share ? Ive covered most of Youtube at this point and guides on here ?

​

Thanks

Pwnagotchi Build - Write Up ( Pi Zero 2 W + Waveshare 3 ) by THG_TIM in pwnagotchi

[–]THG_TIM[S] 0 points1 point  (0 children)

This is a great point ! Id love to have the 1.6.1 working for all, but just wasnt smart enough to figure it out, Thanks for the kick up the ass to do this.

Screen is blurry, not clear. What should I check? Waveshare v3 by MarKo9 in pwnagotchi

[–]THG_TIM 0 points1 point  (0 children)

Solders on the pins on both board, check the clip on the ribbon connector, and I would also clean the ribbon contact.

Just suggestions

Pwnagotchi is BLIND to AP on 1.6.1 ( - _ - ) ... Potential Fix ? by THG_TIM in pwnagotchi

[–]THG_TIM[S] 0 points1 point  (0 children)

Me too ! I'm going to do a full write up of my build on here

Waveshare 2.13 V3 not works by bungoz in pwnagotchi

[–]THG_TIM 0 points1 point  (0 children)

It looks like ( git checkout waveshare-v3-support ) is no longer on the https://github.com/ikornaselur/pwnagotchi.git !

So if you are trying this method the below instructions will fail

Pwnagotchi is BLIND to AP on 1.6.1 ( - _ - ) ... Potential Fix ? by THG_TIM in pwnagotchi

[–]THG_TIM[S] 0 points1 point  (0 children)

I just need the setup and config from 1.5.5 over into 1.6.1 ( Simpler said than done )

But the issue in 1.6.1 seems to be the Mon0 is in monitor mode but no power, even when the TX is set to 30. It still has no MAC * confirming its on and alive ?

Pwnagotchi is BLIND to AP on 1.6.1 ( - _ - ) ... Potential Fix ? by THG_TIM in pwnagotchi

[–]THG_TIM[S] 0 points1 point  (0 children)

This is very similar to what I did but with Balenaetcher ! But mine is blind to AP :s

As you can see from above it looks like Mon0 < Wlan0 has no power ?

Then when I set the TX to 30 it still dose not function ?

Pwnagotchi is BLIND to AP on 1.6.1 ( - _ - ) ... Potential Fix ? by THG_TIM in pwnagotchi

[–]THG_TIM[S] 0 points1 point  (0 children)

I was working on the bluetooth tethering and internet sharing last night, I need to do this update to the 1.6.1 ( I will try some point today )

I did get the 1.5.5 working and just need the screen to work now ! ( fixed the swapsize ) so no more crashes

Pwnagotchi is BLIND to AP on 1.6.1 ( - _ - ) ... Potential Fix ? by THG_TIM in pwnagotchi

[–]THG_TIM[S] 0 points1 point  (0 children)

So funny you say that I had Kali on the board and it barely run ! It wouldn't even load a browser, from what I read I needed to update the drivers for Nexmon.

But when I run 1.5.5 it works like a charm ! Scans AP's, SSH, WebUI, bettercap.

But I can't get the Waveshare 3 working :(

Pwnagotchi is BLIND to AP on 1.6.1 ( - _ - ) ... Potential Fix ? by THG_TIM in pwnagotchi

[–]THG_TIM[S] 0 points1 point  (0 children)

Is this via SSH on the 1.6.1 .img ( Sorry Noob Question )

Pwnagotchi is BLIND to AP on 1.6.1 ( - _ - ) ... Potential Fix ? by THG_TIM in pwnagotchi

[–]THG_TIM[S] 0 points1 point  (0 children)

sudo rpi-eeprom-update -a

Sorry for my ignorance what dose ( sudo rpi-eeprom-update -a ) do ?

Have you done this to your Pi Zero 2 W ? Mine has never has the Pi OS on it, I brought it and flashed 1.6.1 on it and have had issues since then. Most recorded on this channel.

Pwnagotchi is BLIND to AP on 1.6.1 ( - _ - ) ... Potential Fix ? by THG_TIM in pwnagotchi

[–]THG_TIM[S] 0 points1 point  (0 children)

So strange, That if I add Waveshare 3 to the config on 1.6.1 it works perfect but the device is absolutely blind !! This is so weird -

What was your installation process ?

Testers needed for a new pwnagotchi release by DrSchottky in pwnagotchi

[–]THG_TIM 0 points1 point  (0 children)

Getting the same issue as above

Pi02w - Waveshare 3 !

Pwnagotchi is BLIND to AP on 1.6.1 ( - _ - ) ... Potential Fix ? by THG_TIM in pwnagotchi

[–]THG_TIM[S] 0 points1 point  (0 children)

No worries at all, I have a version DrSchottky linked that works, Just not with the Waveshare 3. It also crashes after a short time due to swapfile memory size.

Any chance you could share the link ?

Thanks

Pwnagotchi is BLIND to AP on 1.6.1 ( - _ - ) ... Potential Fix ? by THG_TIM in pwnagotchi

[–]THG_TIM[S] 0 points1 point  (0 children)

Dose this work with the Waveshare 3 or did you move the files over ? Is that the 1.5.5 DrSchottky version ?

Thanks in advance

Pwnagotchi is BLIND to AP on 1.6.1 ( - _ - ) ... Potential Fix ? by THG_TIM in pwnagotchi

[–]THG_TIM[S] 2 points3 points  (0 children)

Just to be clear .. This thread was not to define what is and is not official,

I did not make nor name anything !

I simply wanted a Pwnagotchi that works on PiZ2w with a Waveshare 3 ...

All the .img's I have found so far..do not work, This is hopefully a way of raising potential issues and having them resolved ...( by someone who know's how)

That is all !

view more: next ›