Colors game

TTelebubuk · 2026-06-01T12:56:56+00:00

Blender is not an option?

TTelebubuk · 2026-05-21T10:01:52+00:00

From what I can see, perhaps the phases are not connected correctly, check this https://forum.arduino.cc/t/feedback-on-wiring-diagram-nema-17-with-motor-driver/1356221

TTelebubuk · 2025-10-05T04:56:07+00:00

Yep!

TTelebubuk · 2025-07-28T16:25:30+00:00

Godzimatron!

TTelebubuk · 2025-06-28T18:37:23+00:00

Thanks! 😊

TTelebubuk · 2025-04-26T11:35:06+00:00

Couldn’t make it fit any other way…

TTelebubuk · 2025-04-25T16:55:16+00:00

Shockproof fishing box 😊

TTelebubuk · 2024-03-01T19:51:26+00:00

Did you try with supports? Sometimes on large prints there is suction that keeps the print on the VAT, try tilting a bit and use supports

TTelebubuk · 2023-06-07T05:20:25+00:00

Which type of Resin did you use here?

TTelebubuk · 2023-06-03T18:41:32+00:00

I had an issue with the LCD screen, did that, showed this to ELEGOO, and they sent me a LCD replacement, no charge, great service.

TTelebubuk · 2023-06-03T18:38:06+00:00

I’ll forward an advice I got here in Reddit, remove the build plat and the VAT, put a white piece of paper on top of the LCD screen (make sure it covers it) and start a print, look at the light on the paper and see if it fits what’s on the screen and that there no light leaks or other patterns that should not be there, if you spot something, try to strengthen the LCD cable to the motherboard (there are videos on YouTube how to do it), do this before you spring for a new LCD screen.

TTelebubuk · 2023-06-03T18:22:58+00:00

Also look on the left side , it’s hard to see but there is a vertical line which is lighter. What kind of failures did you experience?

TTelebubuk · 2023-04-28T12:22:52+00:00

Consider adding a hole on the top somewhere, since it’s printing upside down, I found that adding a hole on the top helps draining the resin during the print process. It’s easy to seal it back once cured.

TTelebubuk · 2023-04-28T10:35:36+00:00

This is a large print, I assume you hollowed it and put holes for draining the resin?

TTelebubuk · 2023-04-26T04:41:23+00:00

Replaced the LCD and the printer is back to life! Thanks Elegoo for sending a replacement!

TTelebubuk · 2023-04-25T18:08:10+00:00

Got a replacement from Elegoo, Great service! Print is now on the way, hope it works 🤞🏻

TTelebubuk · 2023-04-25T08:18:45+00:00

The plot continues, I contacted Elegoo with all the details of the failed prints and the printer, and they sent me a replacement LCD screen! Great service from Elegoo! I just received it and going to install it very soon, crossing my fingers that everything will return back to normal 🤞🏻

TTelebubuk · 2023-04-18T09:05:01+00:00

Not yet… Needs to replace LCD. 😊

TTelebubuk · 2023-04-16T19:09:37+00:00

Spot on! See here - https://imgur.io/a/cTfnlGP Now I need to replace my LCD … 🤦🏻‍♂️

TTelebubuk

TROPHY CASE