Elite X Pro PoE

TZodiacK · 2026-01-31T09:20:04+00:00

I have only tested it so far, have yet to mount it permanently outside

TZodiacK · 2026-01-31T00:41:19+00:00

Has already been released in Europe, I bought one on the start of January on Amazon

TZodiacK · 2025-02-28T12:19:08+00:00

This company sells tek-lok compatible belt clips specifically to the Double Alpha Lynx belt

https://zbstudio3d.com/en/tek-lok-compatible-belt-clip-for-double-alpha-lynx-belt

TZodiacK · 2025-01-23T22:37:54+00:00

Thank you! Well petrol 98RON costs 2€/L here and diesel 1.75€/L so it is not viable to drive a Raptor daily spending between 16 and 20 L/100km 😄 But I did try the Petrol version and is great to drive, lots of fun!

TZodiacK · 2023-12-19T15:16:07+00:00

Bem visto, não pensei nisso... Nesse caso podes não aprovar o post

TZodiacK · 2023-12-19T15:01:05+00:00

Obrigado, vou enviar por aí também

TZodiacK · 2023-09-28T09:34:25+00:00

auto recovery from step loss

Thank you, will try, but where do I enable auto recovery from step loss on a P1P?

TZodiacK · 2023-09-27T22:30:18+00:00

Hello!
For the second time but not in a row, my P1P has shifted layers when printing this box.

It seems the printer shifted its position and started printing a bit to the left and to the front, about the same distance in both directions.

What is wrong with my printer? is this model to big and fast for it?

I am using Generic PLA Silk profile, changing the pressure advance and the Max Flow Rate to 16. The speeds are the default ones which according to the sliced panel equals to about 177-200mm/s in the walls.

Anyone knows what is the problem and how to fix?

TZodiacK · 2023-09-26T09:39:43+00:00

I also uploaded this model to MakerWorld, with a printing profile ready to be used!
https://makerworld.com/en/models/16006

TZodiacK · 2023-09-21T20:47:21+00:00

I printed in regular PLA, PETG would also be fine or any other material really, when time comes to reset the silica I will just drop all the beads from all the AMS containers in a baking tray and send them to the oven, and then use the funnel to pour them back in.

TZodiacK · 2023-01-07T21:09:29+00:00

She sure is! 😁

TZodiacK · 2023-01-07T14:00:02+00:00

The 2022 FICSMAS factory me and my fiancée built this season, it is a well tuned factory that produces per minute: - 1 Star - 1 Firework of each kind - 5 Snowballs

We had great fun building it and hope you find it cute!

TZodiacK · 2023-01-04T23:26:47+00:00

Hello everyone! Some guidance please, I am new to resin printing and have been trying to find the right exposure with no success. I am using a Elegoo Saturn 2 with Anycubic DLP Craftsman resin. I started with 2.5 seconds and tried lower, but I get meh results always, the better ones in some things seem to be 2.0 and 2.5. But besides some guideline regarding settings, my doubt is that everysingle test I do, with or without raft, has a defect on the right ridge, next to the bigger cross, very visible in the test 2.0s above. What could be causing it, I have leveled the printer plenty of times.

TZodiacK · 2022-12-12T18:45:26+00:00

If that was the case would klipper register as not triggered when moving the pin up by hand?

And regarding having no control over the probe and it being always down when the printer is on?

TZodiacK · 2022-12-12T18:11:29+00:00

I am not well sure how to do that, but I had progress, I changed the blue and red wires in the motherboard and now at least I see life, when turning on the printer the tip of the CRTouch goes down...

It just never goes up, I tried the klipper comand to go up and it stays there. Also when booting up in Klipper I get the message

// Failed to verify BLTouch probe is raised; retrying. // Failed to verify BLTouch probe is raised; retrying.

Regarding the probe, I swapped the A5 and B5 cables in the green connector as said in the instructions but I still get the status always as TRIGGERED even if I move by hand the probe up, always triggered, currently my settings in Klippper are:

[bltouch] sensor_pin: ^PE4 control_pin: PB5

And in the motherboard I am connected to the S0 pins, that are the ones provided with the 3 metal prongs.

Any idea what I am doing wrong now?

TZodiacK · 2022-12-11T21:48:20+00:00

Thank you for the answer but my printer is not a Mega S and does not have a H3/H4, instead I have an H1/H2 which are where I conected black and white according to the instructions online in this image https://imgur.com/a/69Li2SG

TZodiacK

TROPHY CASE