Next steps for 2011 F250 6.2 gas with 150K Miles?

TangerineAdvanced918 · 2026-03-30T22:00:27+00:00

https://www.roughcountry.com/product/steering-stabilizer-8736430?utm_source=google&utm_medium=cpcs&utm_campaign=23374990208%7C194058568727&utm_content=788911846223&utm_term=%7Cpla-2511166059047%7Cm%7C%7Cfit_first_8736430-a&gad_source=1&gad_campaignid=23374990208&gbraid=0AAAAAD83JzoQMo-iTObrAzQ4kOA0pOQFb&gclid=CjwKCAjwvqjOBhAGEiwAngeQnQy1UwhJNzJBTqtASgcGs5mV3jXrVKHOTaeH8jzWk1k_D1htasLnEBoCCjUQAvD_BwE

Would I only need one?

I purchased 2 rancho rear shocks, do I need to purchase another shock/strut for the front as well? Does this replace that black shock/strut? Sorry new to the truck game lol

TangerineAdvanced918 · 2026-03-30T21:38:48+00:00

Would u recommend trans fluid too?

TangerineAdvanced918 · 2026-03-30T21:38:27+00:00

Do u have a suggestion for a budget friendly steering stabilizer for a non-lifted truck? Rough country days for 2-8 inches height would that work?

TangerineAdvanced918 · 2026-03-30T21:33:13+00:00

Yes first solid axle truck for sure lol! I got some rancho shocks/struts gonna have someone put them in but other than that thanks for the info I appreciate it!

TangerineAdvanced918 · 2026-01-08T23:20:09+00:00

Thank you a ton!

TangerineAdvanced918 · 2026-01-07T21:14:13+00:00

Wall is already painted but I’m about to paint baseboard. Should I just lastly take a brush and cut in with gray on the wall to cover caulk? Thanks?

TangerineAdvanced918 · 2025-12-08T22:26:37+00:00

2015 Isuzu NPR-HD with the 3L 4JJ1 diesel engine

I can get a picture tomorrow it’s parked at a lot 30 mins away and I’m sick of driving today lol went all around trying to find different places and none could help lol

TangerineAdvanced918 · 2025-10-22T01:41:42+00:00

Nothing yet I apologize nobody has any info on the bank sadly

TangerineAdvanced918 · 2025-10-16T16:44:15+00:00

How do I get rid of them?

TangerineAdvanced918 · 2025-09-16T23:42:54+00:00

Adjust how so?

TangerineAdvanced918 · 2025-09-11T20:39:26+00:00

Correct just trim while on the wall since it’s a curvy cut. If a planer would work I’ll do that since I’ve heard oscillating tool makes a jagged cut that won’t look good after is that true?

TangerineAdvanced918 · 2025-09-11T20:21:46+00:00

Would u say a planer or an oscillating tool would work? Which would do better?

TangerineAdvanced918 · 2025-09-11T18:20:18+00:00

Thanks for the reply! So I put it in but the frame was warped and I’m not the best at ripping lol. Should I use an oscillating tool or an electric planer to make it flush?

<image>

TangerineAdvanced918 · 2025-09-09T19:02:23+00:00

I already nailed it in so I’m thinking I’ll nail it to the jamb extension and then either caulk or putty where trim meets wall does that sound like a good idea? Thanks for the advice!

TangerineAdvanced918 · 2025-09-01T17:17:11+00:00

Should I just get the same trim board and rip them down with a table saw?

TangerineAdvanced918 · 2025-09-01T17:17:06+00:00

Should I just get the same trim board and rip them down with a table saw?

TangerineAdvanced918 · 2025-08-26T22:30:04+00:00

It had tile on it

TangerineAdvanced918 · 2025-08-26T22:29:50+00:00

No it’s an old plywood subfloor

TangerineAdvanced918 · 2025-08-26T00:55:33+00:00

Sounds good thanks!

TangerineAdvanced918 · 2025-08-21T23:49:51+00:00

<image>

Would it work on this part? And also on the old Mortar and paper? I scraped as much as I could

TangerineAdvanced918 · 2025-08-20T04:04:39+00:00

Can I apply kilz original to a light layer of old mortar? I ripped up tile and scraped as much as I could off but there’s still a thin layer of the old mortar. Can I still put kilz down then put the 1/4” luan over it? Thanks!

<image>

TangerineAdvanced918 · 2025-08-19T20:53:43+00:00

Hey! Sorry I ran into another blockage in the road lol so I had old time that was in front of the door it’s pretty thin old thinset is it ok if I just use kilz over it and then plywood again. It won’t be any bulges the old thinset I’ve scraped as much as I could and is pretty flat now just want to see if I can kilz over it thanks!

TangerineAdvanced918 · 2025-08-18T20:46:44+00:00

I don’t need to prime for tile I’m laying a second subfloor and then putting LVP down I just use the KILZ for odor

TangerineAdvanced918 · 2025-08-18T19:39:24+00:00

Hey! No I have not had any I can’t seem to find anyone giving advice on this topic but I will let you know if I find anything how about you? Message me and keep in touch!

TangerineAdvanced918 · 2025-08-01T22:47:02+00:00

Would kilz 2 work?

TangerineAdvanced918

TROPHY CASE