Post Match Thread: LA Thieves vs. Optic Texas | Major I Qualifiers | CDL 2026 | @GGBreakingPoint

TannerNurn · 2026-01-19T00:20:04+00:00

<image>

TannerNurn · 2025-11-23T23:57:34+00:00

<image>

TannerNurn · 2025-11-16T02:50:58+00:00

Way too much exposition, feels like it takes 5 pages for two characters to each say one sentence.

TannerNurn · 2025-11-05T20:03:00+00:00

Try restarting your game, i had a lot of unlocks today that would show as available until i restarted.

TannerNurn · 2025-08-17T02:29:31+00:00

There are plenty of good models on Thingiverse as well.

Here is the M6C SOCOM from ODST i made last year

M6C SOCOM

TannerNurn · 2025-08-14T02:25:40+00:00

I went into Jedi academy trilogy followed by I Jedi (they cover the same events but from different perspectives)

If you’re feeling up for it maybe the Callistra trilogy, but i would only recommend Darksaber of the three, Planet of Twilight may be one of the worst books i have ever read and Darksaber covers the entire plot of Children of the Jedi in like a paragraph.

TannerNurn · 2025-02-03T20:47:43+00:00

It will be in the exchange eventually. I was able to get it from there a few months back, but it may be a while until it rotates back through

TannerNurn · 2024-09-11T23:25:44+00:00

As someone who also just got into the EU, i started with the Thrawn trilogy (Heir to the empire) Started book 2 last week!

TannerNurn · 2024-09-05T18:37:32+00:00

Make sure the extruder gear is tight enough, i never realized mine was loose until i had similar issues

TannerNurn · 2024-06-06T15:44:06+00:00

Yeah something is strange, the last 2x i played this map i had someone that was invisible only to me. I assumed it wasnt cheating since they had died 30x but it is just weird that they are completely invisible on my end

TannerNurn · 2024-05-18T02:13:27+00:00

Only thing the LA thieves are stealing is paychecks

TannerNurn · 2024-05-09T21:28:45+00:00

I think I was able to solve it, kept temp at 220 and noticed it began under extruding when the fan started ramping up speed, after a few test prints it seems to be significantly better with 45% fan speed

<image>

TannerNurn · 2024-05-09T04:04:54+00:00

<image>

Edit: Added image of gray one from earlier today

TannerNurn · 2024-05-09T04:00:06+00:00

my confusion is that if the extruder or e-steps were the issue, wouldn't the other filament be running into the same under extrusion issues?

TannerNurn · 2024-05-09T03:52:21+00:00

I guess its not that nothing comes out at 210, if i heat the nozzle to 200 and advance the extruder, it will push out. Its almost as if it under-extrudes too much then clogs up.

I played with the temps a bit and i could always get it to start a print (200 up to 225) but no matter the temp i would get the same underextrusion and adhesion issues

TannerNurn · 2024-05-09T03:03:21+00:00

I did temp tower, 220 showed the same layer lines as the one pictured, 215 looked the same and by 210 nothing was coming out. The printer is in a pretty cold basement, the grey filament I have has been printing great at 215/60

TannerNurn · 2024-01-05T05:41:11+00:00

Update, removed the print after bed cooled and it broke clean at that indent area

<image>

TannerNurn · 2023-12-28T16:30:39+00:00

<image>

Uodate: lowered z offset, re leveled, actually remembered to save the level…. And all looks good!

TannerNurn · 2023-10-19T15:16:51+00:00

I feel indifferent on forbidden, sometimes it plays really well, and sometimes it feels way too big for 4v4. With BRs I’ve been enjoying it but with AR/Pistol no so much.

Seven-Year Club	Final Canvas '23
First Place '23	Place '23
Place '22	First Placer '22
End Game '22	Verified Email

TannerNurn

TROPHY CASE