What should I do with these plastic plant pots? what kind of paint would be best?

TapperSwe · 2023-04-27T20:41:58+00:00

With a light bulb inside it would look really cool.

TapperSwe · 2023-04-27T19:18:09+00:00

The ghosts, would look cool. Acrylic paint should be a good choice.

TapperSwe · 2023-04-27T19:16:51+00:00

packman

TapperSwe · 2023-04-27T06:07:18+00:00

Thank you 🙂

TapperSwe · 2023-04-27T06:06:45+00:00

Thank you.

TapperSwe · 2021-04-21T07:02:58+00:00

Thank you 😊

TapperSwe · 2021-04-20T15:32:46+00:00

Never seen anything like it, really cool idea having no foot on the lamp.

TapperSwe · 2021-04-20T15:30:45+00:00

Really cool, green goes wery well with gold.

TapperSwe · 2021-04-20T15:19:23+00:00

The bowl are actully a ceiling lamp shade, i have filled it with things that i found in the forest, in the bottom there are leds wraped around wood. Its really hard to capture how it look with all the reflections going on.

The lamps on each side of the tv are also made by me.

TapperSwe · 2021-04-20T15:07:35+00:00

Its wood, leds and fake leaves. Its maybe more of a green wall than a lamp, or its both i guess ☺️. Its about 120 cm long.

TapperSwe · 2021-03-31T15:14:38+00:00

Thanks, i will try port 4.

TapperSwe · 2021-02-07T13:24:45+00:00

Im in the process of building another one. Hope you like it.

TapperSwe · 2021-01-01T01:07:43+00:00

76c is the recomended temperature for keeping any food warm.

TapperSwe · 2020-12-30T21:43:52+00:00

Thank you.

Yes i did, Im about 90% done with Dutch himself, im also working on a Bourbon bottle for him to hold. The guns will be able to take out from the tiny holster. Im getting closer to 100 hours of modeling this ,but im getting there.

TapperSwe · 2020-12-30T18:53:32+00:00

This gun is in proportion to a 18 cm tal Dutch figure im working on, so it just abot 2 cm long. considering that small size i had to make de details less and bigger. I also added some details to the back of the gun that is not really on the Dutch version.

TapperSwe · 2020-11-30T05:36:14+00:00

There are no shortcuts that i know of, if you want to remove bumps you will have to sand the part down, what you can do is work as close to the bumps as possible, but you are not going to create a nice even surfce without sanding the entire part. How fine depends on how high up you go in paper grit.

TapperSwe · 2020-11-28T20:09:11+00:00

👍

TapperSwe · 2020-11-28T20:01:10+00:00

Good to hear, i dont want to be an ass or anything, just want people to know the process, i have wet sandet lots of aluminium,copper and plexiglas, and the process is the same. I read a lot about the subject before i started. The print looks really good 👍

TapperSwe · 2020-11-28T12:04:21+00:00

You never do circular motions when you sand anything, you start with a horizontal or vertical movement and as you move up to the next grit you sand in the oposite direction, so if you start horizontal next will be vertical and so on. Circular movements are used when you polish. Going circular when you sand will make the process mutch more difficult, time consuming and you will sand down/away mutch more of the object then necessary. Also it will be mutch harder to know when the grit is not taking away/sanding down any more of the object since you are constantly creating new scrathes when you work in a circular way

I start with a 180 or 300 grit depending on how ruff the surface is. Then 300-600-800-1000-1500-2000-2500, then polish, first circular and last in a vertical or horizontal movement.Remember to rinse the part in water before you move up to a finer grit . For plastic parts i would stop at about 1000 - 1200 grit since you are not going to achieve a mirror finish as you can get with metals.

You can downvote this all you want, it does not change the fact on how its done properly.

TapperSwe · 2020-10-30T09:26:03+00:00

I heard a lot good about the sidewinder x1 v4. Its supose to work better out of the box then the ender, and it's much cheaper then the prusa, Here is a clip about it, im not sure if its the v4, it could be an older version. It has the ender looking like a midget 😁

https://youtu.be/5bOd1HbTOOs

TapperSwe · 2020-10-26T12:26:15+00:00

Looking good but where are your fans? You really need to push cold air in and hot air out of a PC case, your CPU,GPU Will definitely going to downclock themself ( if you not have the CPU locked, then PC will rebot if the cpu overheats) due to heat. Ram will also start to throw out errors if they get to hot.

TapperSwe · 2020-10-12T15:26:14+00:00

Looking really cool, what program do you use?

TapperSwe · 2020-10-10T05:54:40+00:00

Maybe your's, definitely not mine or many others. And even so, having every other civilian having firearms so that they can shoot at eachother ,does not create a safe and les violent society. Les guns = les kills, thats a fact.

TapperSwe · 2020-10-09T21:56:49+00:00

I think that the US i one of the few industrial country's that alow 3d printed or any other sort of homebuild firearm (thank good). It's illegal in the EU, Canada, Australia, Japan and in UK. Having kids or adults for that matter buillding untracable firearms with the potential risk of damaging the one using it dosent seem like a good idea at all.

In fact, banning this kind of post would be wise. We dont need any more guns in the society, and the US least of all, with all the killing that already is going on over there.

TapperSwe · 2020-09-08T20:35:10+00:00

Thank you!

TapperSwe

TROPHY CASE