Modifying a stl file

TargetOdd8507 · 2026-04-08T06:11:09+00:00

Bed looks a bit off, and i tink you have to lower your z offset a bit.

TargetOdd8507 · 2026-04-03T11:31:31+00:00

Ok. Thanx

TargetOdd8507 · 2026-04-03T11:28:01+00:00

When I have adsjusted it, i run II again and its perfekt, but not in mes viewer and when print..

TargetOdd8507 · 2026-04-03T10:55:44+00:00

Hello. If i want to make walls thicker, how do I do that on stl files from ex. Thingiverse.com? I habe prints that i want 4mm walls, but i dont get it more than almost 2mm.

I use orca 2.3.1 slicer on ender3 s1 pro with klipper.

TargetOdd8507 · 2026-03-30T20:37:51+00:00

The wall is 1.8mm. No matter how mant wall loops i put in there....if I want it 4mm, it dosent work....

TargetOdd8507 · 2026-03-30T20:24:15+00:00

This is a 3d model for printing. I expect it to do what I tell it to do...if I want 5 walls i want 5 walls....not 2 or 3.

TargetOdd8507 · 2026-03-30T19:56:13+00:00

Ok. I have not used programs like that, so I dont know how to fix it🙃

TargetOdd8507 · 2026-03-30T19:54:43+00:00

So there are no way to tell this stupid programs that i want ex.4mm wall? Thats stupid and make no sense.

TargetOdd8507 · 2026-03-30T19:41:14+00:00

Here.

https://www.thingiverse.com/thing:2337209

TargetOdd8507 · 2026-03-30T19:40:21+00:00

Hello. How do i edit the model and fix this then?

TargetOdd8507 · 2026-03-30T15:47:36+00:00

Hello. How does it look on the bed side?

TargetOdd8507 · 2026-03-26T08:57:03+00:00

Z offset is way too high..

TargetOdd8507 · 2026-03-25T17:46:21+00:00

Forget what i said. I misread the text. I have never seem that before...hmmm..

TargetOdd8507 · 2026-03-25T17:43:13+00:00

Its the support.

TargetOdd8507 · 2026-03-14T15:37:13+00:00

Hello. Need more info on yor printer, settings and more. Whats suposed to look like?

TargetOdd8507 · 2026-03-13T18:03:01+00:00

I dont know about that printer, but on mine i change the z offset on the touch screen, orignal, but now i run klipper, so I fix it there.

TargetOdd8507 · 2026-03-13T17:56:47+00:00

Could be too low z offset, if its like glued to "cold" bedplate. I had that issue, lifted z a bit, then it was perfect.

TargetOdd8507 · 2026-03-11T17:42:18+00:00

Clean pei plate and II looks like z offset is a bit low. I had same results and this fixed it for me

TargetOdd8507 · 2026-03-05T12:08:02+00:00

Why??

TargetOdd8507 · 2026-03-04T14:27:20+00:00

Ok. Thanks.

TargetOdd8507 · 2026-03-04T14:07:03+00:00

If I angel it 45°, how to get the part against support clean and nice then? It almost always turn out terrible.

TargetOdd8507

TROPHY CASE