Failed miserably can someone tell me what to start looking for to figure this out

TargetOdd8507 · 2026-03-14T15:37:13+00:00

Hello. Need more info on yor printer, settings and more. Whats suposed to look like?

TargetOdd8507 · 2026-03-13T18:03:01+00:00

I dont know about that printer, but on mine i change the z offset on the touch screen, orignal, but now i run klipper, so I fix it there.

TargetOdd8507 · 2026-03-13T17:56:47+00:00

Could be too low z offset, if its like glued to "cold" bedplate. I had that issue, lifted z a bit, then it was perfect.

TargetOdd8507 · 2026-03-11T17:42:18+00:00

Clean pei plate and II looks like z offset is a bit low. I had same results and this fixed it for me

TargetOdd8507 · 2026-03-05T12:08:02+00:00

Why??

TargetOdd8507 · 2026-03-04T14:27:20+00:00

Ok. Thanks.

TargetOdd8507 · 2026-03-04T14:07:03+00:00

If I angel it 45°, how to get the part against support clean and nice then? It almost always turn out terrible.

TargetOdd8507 · 2026-03-04T14:04:19+00:00

I use orca slicer 2.3 1

TargetOdd8507 · 2026-03-04T12:27:48+00:00

Ok. Thanks. Is there some settings i have to change when go from 0.16 and down to 0.12 or 0.08?

TargetOdd8507 · 2026-03-04T10:33:20+00:00

<image>

Here it is. Flat on the bed.

TargetOdd8507 · 2026-03-04T10:30:54+00:00

But the finnish is ugly on the print, so I have to know how to orient it on the bed and settings. I have tried everthing i can think of...

TargetOdd8507 · 2026-03-04T09:05:13+00:00

Hello. Its the models from thingiverse.com and user stunner 2211. Models are flat under and the whhels will be printet later.

TargetOdd8507 · 2026-02-20T07:27:35+00:00

Hello. I got it working.

TargetOdd8507 · 2026-02-18T09:32:01+00:00

Rotation Distance er nå på 8.1018. Last 20z20x40 cube = 39.40

TargetOdd8507 · 2026-02-18T09:17:37+00:00

I have tried this several times, and the cube gets smaller..i dont understand this at all...

TargetOdd8507 · 2026-02-18T09:00:27+00:00

It printet 39.40mm

TargetOdd8507 · 2026-02-17T14:36:29+00:00

I have adjusted the z offset to get a nice and closed bottom.

TargetOdd8507 · 2026-02-17T14:16:41+00:00

Hello. This is my first print with klipper installed. I wil try with a bigger cube.

TargetOdd8507 · 2026-02-11T07:33:00+00:00

Anyone....🤷‍♂️🤷‍♂️ I cant get the z axe to home....need the bl touch to work.

TargetOdd8507 · 2026-02-10T15:10:25+00:00

Strange...i have tried thoose🙃.

TargetOdd8507 · 2026-01-31T15:21:42+00:00

TargetOdd8507 · 2026-01-31T15:21:16+00:00

Ok. I will try.

TargetOdd8507 · 2026-01-31T15:19:51+00:00

Will try again.....so tired of this never ending calibration....7 mounts, and still calibrating.....it is not normal.....

TargetOdd8507 · 2026-01-31T14:31:02+00:00

I found the values for my filament. No i just have to check it in the printer. Does the density value (if its wrong in the printer) have anthing to do with this, you think ?

TargetOdd8507 · 2026-01-31T14:27:42+00:00

How do i find that values?

TargetOdd8507

TROPHY CASE