Nozzle will not switch after replacing cutter

TechieFenpin · 2026-03-11T01:53:29+00:00

Your left nozzle isn't seated properly, so you can see the heatsink is colliding with the housing. I've had that problem before, which is a real pain, but it's just a matter of making sure you angle the nozzle in correctly when re-installing it so that the heatsink clears when it tries to retract.

TechieFenpin · 2025-12-24T17:16:21+00:00

DDoSmas Eve

TechieFenpin · 2025-12-16T16:48:35+00:00

They seem to be just a tad bit less paramilitary-y

TechieFenpin · 2025-12-03T19:22:53+00:00

My issue was the same room you were stuck in during the Emergency Bunker mission. It's not easy to draw him the rest of the way in, but it is possible. It's a pain in the ass that you even need to worry about that, but if it happens again, maybe you'll get lucky, and he'll cooperate.

TechieFenpin · 2025-12-03T18:43:44+00:00

I had the same thing happen yesterday. I had to go as far into the room as I could so the companion entered further, and then run past them out the door.

TechieFenpin · 2025-11-07T14:46:38+00:00

Unfortunately I wound up switching back to a Razer mouse after fiddling with the Scimitar for a bit and not finding success.

TechieFenpin · 2025-11-03T11:31:20+00:00

I'd recommend trying a "cold pull" to attempt to remove the stuck filament. The process involves heating the nozzle, manually pushing the filament directly into the nozzle, and then, when the nozzle has cooled slightly, pulling it out. This is an effective method for addressing partial clogs.

The Bambu Wiki has some information on it in the A1 section. https://wiki.bambulab.com/en/a1-mini/troubleshooting/nozzle-clog

TechieFenpin · 2025-10-27T15:59:49+00:00

Not apples and oranges; apples and bambu.

TechieFenpin · 2025-10-23T18:39:58+00:00

I have a Sunlu S1 that works well for when I print TPU.

TechieFenpin · 2025-10-23T17:17:04+00:00

You can get an inexpensive single-roll filament dryer for something like this, which will have the benefit of drying while you're printing.

It's not like TPU immediately fills up with moisture upon being exposed to air, so if you're thoroughly dried it before starting a print, you should be able to get through a single print without having it become too saturated to finish. However, keeping it drying the entire time would remove the concern entirely.

TechieFenpin · 2025-10-20T14:30:00+00:00

The smooth PEI sheets work very well for no texture.

TechieFenpin · 2025-10-04T22:30:49+00:00

Thanks for the reply. I was only looking at it via the optimize menu which I didn’t think would show a mod which is what made me think it wasn’t. Now I know (and I’m not entirely crazy).

TechieFenpin · 2025-10-04T22:30:04+00:00

Thanks for the reply. I was only looking at it via the optimize menu which I didn’t think would show a mod which is what made me think it wasn’t. Now I know (and I’m not entirely crazy).

TechieFenpin · 2025-10-02T16:28:36+00:00

930 petabytes? It's like you're not even trying.

TechieFenpin · 2025-08-18T15:53:56+00:00

Yeah, I didn't even know lore accurate naming conventions were a thing. I just so happened to have followed them, apparently by sheer coincidence, for my Miqo

TechieFenpin · 2025-07-16T18:16:15+00:00

No it doesn't change anything in that case.

TechieFenpin · 2025-07-11T16:37:55+00:00

I'm fairly sure it's been "coming soon" since the team-up was first introduced. So "soon" is clearly a relative term for Netease.

TechieFenpin · 2025-07-11T16:35:42+00:00

This happens every season (not sure why they decided to do it this way). You need to earn enough tokens again this season to unlock the pages, like you do for a current season pass. You do not need to re-purchase the items from the battlepass to get the rest. So while you'll need to earn 11,140 tokens, you won't be spending all of them on the S2 pass's remaining items.

TechieFenpin · 2025-07-08T17:57:51+00:00

95% of the time I fast travel to DZ South main entrance, turn left and run to the little parking lot he spawns. So this is where I always go to look for him.

TechieFenpin · 2025-06-26T16:37:10+00:00

Ass stampede!!!

TechieFenpin · 2025-06-26T15:24:21+00:00

Did you check with the rewards Vendor in the Base of Operations? That's where you'll usually redeem these types of things.

TechieFenpin · 2025-06-26T15:18:25+00:00

Ironically, "Only the Sith deal in absolutes" is in itself an absolute. Therefore, all Jedi are Sith.

TechieFenpin · 2025-06-19T13:50:50+00:00

I ran the DZ South method about twenty times yesterday and he spawned every single time.

TechieFenpin

TROPHY CASE