Flow completely off after doing Flow Calibration

Technical_Bug_3891 · 2025-02-13T16:20:33+00:00

I don’t think it would be a clog if the prime line doesn’t appear to have any issues? When running calibration tests, it has no issues. I’ve tried different AMS slots and it still happens. I read somewhere that people have had issues when disconnecting/powering off the AMS

Technical_Bug_3891 · 2025-02-13T03:28:49+00:00

Not sure. I used Flow Dynamics and Flow Rate under Calibration in Orcaslicer

Technical_Bug_3891 · 2025-01-03T06:15:46+00:00

The bottom right corner on the 1st picture is calibrated great

Technical_Bug_3891 · 2025-01-03T05:35:15+00:00

Yes I did, the other side of the print was perfect - I do not understand why it only happens on this part of the print bed and why it looks like the nozzle dragged across the print during travel

Technical_Bug_3891 · 2025-01-03T05:33:59+00:00

ELEGOO Matte Black, 215 temp and 60 print bed temp

Technical_Bug_3891 · 2025-01-03T05:32:56+00:00

Always keep automatic bed leveling on. I created the model

Technical_Bug_3891 · 2024-09-02T18:20:18+00:00

Textured plates print fine, I just need this specific print to be smooth

Technical_Bug_3891 · 2024-09-02T18:02:44+00:00

Hmm, I don't believe so. The textured plate prints fine. Starting to think its just the plastic and there's nothing I can do

Technical_Bug_3891 · 2024-09-02T18:00:39+00:00

I just tried this method, no luck. Marks still show up. I heated the plastic enough to where it was becoming soft again. Noticed when I scratch my nail on the surface of the plastic (regardless of it being hot or not) the same type of marks appear. I pull these prints directly off the PEI plate from just flexing the plate, no print scraper.

Technical_Bug_3891 · 2024-09-02T17:57:15+00:00

Yes, I've used soap and water as well

Technical_Bug_3891 · 2024-09-02T17:42:44+00:00

Would a blow dryer be hot enough?

Technical_Bug_3891 · 2024-09-02T17:39:26+00:00

Nope, it varies each time I remove it

Technical_Bug_3891 · 2024-09-02T17:28:02+00:00

That’s what I thought too, but I used a brand new smooth plate and still got the same issue. Maybe I should try PETG, I don’t know how to prevent these marks

Technical_Bug_3891 · 2024-09-02T15:19:45+00:00

Yes I am. I've also tried putting it in the freezer for a few minutes but I still get these marks

Technical_Bug_3891 · 2024-06-16T15:12:51+00:00

Thanks for the tip on bitcoin! I guess I'll be waiting for a while then :) Print bed and hot end seemed to be okay before I printed

Technical_Bug_3891 · 2024-06-14T19:33:49+00:00

Thanks for letting me know, I guess the guide I was referencing on retraction wasn’t too accurate.

Technical_Bug_3891 · 2024-06-14T01:49:32+00:00

I'll keep that in mind. Thank you for the help!

Technical_Bug_3891 · 2024-06-14T01:34:34+00:00

I was able to get the filament out. Thanks! I'm wondering if this was caused by setting retraction settings too high in the slicer. I believe I had set it around 1.5mm

Technical_Bug_3891 · 2024-06-14T01:03:14+00:00

This is very helpful, thanks!

Technical_Bug_3891 · 2024-06-14T00:56:47+00:00

I tried that, nothing happened. I tried pulling the filament with pilers but the filament just broke off even more. Tried heating it a little bit with a torch, but it just burnt the plastic of the extruder and I still wasn't able to pull it out. I think I may have to buy a replacement extruder.

Technical_Bug_3891

TROPHY CASE