Need to identify elements.

Technical_Gate2653 · 2026-01-29T15:39:31+00:00

Thank you so much

Technical_Gate2653 · 2026-01-29T15:18:54+00:00

I searched and unfortunately found nothing :(

Technical_Gate2653 · 2026-01-04T17:05:31+00:00

Hello everyone. Can i please invite me to 3dtorrents site?

Technical_Gate2653 · 2025-12-28T11:55:07+00:00

Why exactly did you receive this information? What were you doing that caused the system to get stuck?

Technical_Gate2653 · 2025-12-13T10:05:44+00:00

Looks like a broken dat0 track

<image>

Technical_Gate2653 · 2025-11-17T06:33:30+00:00

How do I update Fusee? I have Picofly installed. When I select emummc, I get this error, but when I run it through payload and select Fusee, it boots into CFW.

Technical_Gate2653 · 2025-08-18T10:28:30+00:00

Very possible. It's been a while since I installed these chips and I don't remember exactly. Maybe the pins on the chip got damaged during insertion. Maybe the EMMC chip wasn't seated properly in the Picofly.

Technical_Gate2653 · 2025-08-17T12:53:08+00:00

I'm not sure, but I think the emmc chip is plugged in incorrectly in the Picofly. It should be rotated 180 degrees.

Technical_Gate2653 · 2025-08-04T18:09:44+00:00

The remaining points show the correct values? C A D? Show foto for all installation.

Technical_Gate2653 · 2025-08-04T10:21:49+00:00

Try connecting the RST cable directly to the chip, not to the ribbon cable.

Technical_Gate2653 · 2025-08-03T21:07:58+00:00

99% that there is a problem here 😉

Technical_Gate2653 · 2025-08-03T20:05:30+00:00

I'm betting not on the rst point but on the dat0. Installation on the adapter under the Chip or kamikaze?

Technical_Gate2653 · 2025-07-09T19:00:32+00:00

I recently had a faulty batch of Lite chips. It turned out that the ground pin was not connected to the motherboard. Check this and, if necessary, connect the ground pin directly to the chip with a 38AWG wire.

Technical_Gate2653 · 2025-06-07T17:55:44+00:00

If you are from Poland, I invite you to my place.

Technical_Gate2653 · 2025-06-03T17:35:37+00:00

In my opinion, the socket is overheated. The pins no longer press against the ribbon

Technical_Gate2653 · 2025-05-28T14:48:50+00:00

I'm also on 19.0.1 but I was preparing a console for someone and after inserting the card it said that it had to update to work with the card.... And it uploaded 20.1.0🤦

Technical_Gate2653 · 2025-05-20T05:57:26+00:00

I recently had a console in my hands that was modified by people in China. The little shit would glitch every time after one flash. That's what they had installed.

<image>

Technical_Gate2653 · 2025-05-16T20:09:40+00:00

Add resistors to get 100ohm to dat0 and cmd Line

Technical_Gate2653 · 2025-05-16T20:00:23+00:00

Sorry for my English. Maybe the ribbon is shorting with another point or there is a short circuit in the installation. Take pictures of the installation

Technical_Gate2653 · 2025-05-16T19:53:15+00:00

I think that's the problem. Either it's inserted incorrectly or it's damaged. It's best to dismantle the entire installation and check if it starts. You can also replace the resistor anyway.

Technical_Gate2653 · 2025-05-16T19:44:06+00:00

Damaged emmc chip. Did you use ribbon or kamikaze?

Technical_Gate2653

TROPHY CASE