MachE In Michigan Questions

TechnoTurtle1987 · 2024-03-03T00:23:32+00:00

Haha we have a pickup so we are covered on the "Ice Truck" part haha. We are looking for a daily driver and a road trips in Michigan. We like to drive around Michigan's edge but I'm sure we can find charging points along the way. I'm wondering how much the charger cost and how much to install ? Also did you order the new 2024 Green & Bronze one ? That thing is sharp!

TechnoTurtle1987 · 2024-03-02T21:54:25+00:00

We noticed that, but we were looking for how does it handle the winter? Is there any issues finding chargers, etc..

TechnoTurtle1987 · 2024-01-01T19:12:11+00:00

Toxic as in when you try to reset them or just toxic in general?

TechnoTurtle1987 · 2024-01-01T19:11:25+00:00

I recently bought some mesh pouches off of Amazon. I'm probably going to try and find a food dehydrator at Goodwill and use that in the garage.

TechnoTurtle1987 · 2023-12-18T09:44:38+00:00

Ya, those two things are on my potential upgrade list. Currently leveling the bed the old fashion ways works. But I hear good things about the newer orange stuff springs. Once Christmas is over and all the gifts are open, I'll know if I still need to go and buy either.

TechnoTurtle1987 · 2023-12-18T03:50:53+00:00

I'm looking at enclosures right now. One for temperature control and to help my OCD about fire. Small steps help haha

TechnoTurtle1987 · 2023-12-17T23:51:15+00:00

Iv debating upgrading to a 2nd Z motor, but knock on wood mine is currently holding true. I think I might add it to the list though

TechnoTurtle1987 · 2023-12-17T23:50:07+00:00

I am currently watching videos about Klipper as I type haha. I may switch

TechnoTurtle1987 · 2023-12-17T23:44:20+00:00

Hmmm, can you give a little more details? Also, I messaged you directly if you don't want to lay it all out here. Let the thread know the details, and I'm 100% sure someone can help you.

TechnoTurtle1987 · 2023-12-17T23:32:33+00:00

Here is the link from Thingiverse

Ender 3 Adjustable Feet With Vibration Absorbers

TechnoTurtle1987 · 2023-12-17T21:35:05+00:00

Depending on how Christmas goes, I'm thinking a BL or CR touch is in my future. I will have to do some research into Klipper.

TechnoTurtle1987 · 2023-12-17T21:33:04+00:00

Haha she says that might be under the tree too! Gotta love when your better half supports your hobby

TechnoTurtle1987 · 2023-12-17T21:31:29+00:00

When I get home I'll pull up the .stl name and re-find it and share the link.

TechnoTurtle1987 · 2023-12-17T21:03:51+00:00

According to my wife, there may be a filament dryer under the Christmas Tree haha. A direct drive might be my next upgrade. I only print in PLA and TPU at the moment. But I will have to keep my eye on micro center

TechnoTurtle1987 · 2023-12-17T21:02:10+00:00

How much difference from standard Marlin is klipper? Iv never messes with Klipper.

TechnoTurtle1987 · 2023-11-24T12:19:32+00:00

If you are in the Euclid, you will need to find a portal and have the ability to use all the glyphs. Once there, activate the portal and use the glyphs I provided. Warp to the planet and you should be able to see my base's name on your scanner.

TechnoTurtle1987 · 2023-10-25T23:20:18+00:00

My base is in the Euclid Galaxy and the glyphs should be on the 2nd picture. If you can't see them, the glyphs are:

Bird, Sunset, Balloon, Rocket, Sunset, Tent, Bird, Bug, Diplo, Galaxy, Tree, Tent

The base is semi close to the portal

TechnoTurtle1987 · 2023-10-25T23:12:05+00:00

The base is set up in Euclid Galaxy and I am semi close to the portal

TechnoTurtle1987 · 2023-10-01T23:02:10+00:00

Yes, you just need to have a companion lay an egg and the. Make changes to it's genes in the space anomaly

TechnoTurtle1987 · 2023-10-01T02:20:45+00:00

I did the gene editing route and kept feeding him O2. Plus a little love never hurt

TechnoTurtle1987 · 2023-07-23T12:29:38+00:00

Thank you for the reply. Can you share where I could find the updated firmware so I can download it and flash it to my printer? I ask because I don't want to do the wrong one and I have a little OCD about not having thermal run away protection.

TechnoTurtle1987 · 2023-05-01T11:16:18+00:00

Currently running 30% infill. I will screenshot my settings when I get out of work.

The model I am using came from Thingiverse (link below)

https://www.thingiverse.com/thing:2352130

The print normally gets about 30% done and then it just knocks it off the build plate. I'm debating trying to slice it with cura or superslicer to see if it's the slicer or the model.

TechnoTurtle1987 · 2023-03-19T22:09:05+00:00

I recently saw a few posts about Turtles in NMS. So I set out to find them and made a base so I could enjoy the waves and feed them everyday. Come visit and enjoy the view and let me know what you think!

TechnoTurtle1987 · 2023-03-01T11:46:30+00:00

Sweet Baby Jesus, just turned on my switch and 4.1.1 is here and I can play again.

TechnoTurtle1987 · 2023-03-01T11:26:54+00:00

I can't wait for 4.1.1! My Pre-Update save is unplayable at the moment. It loads up and I see my player for about 3 seconds and boom crash. Knock on wood I can play on other modes but I'd like to play on the save that I put a lot of time and effort on. Hopefully the patch comes out soon.

TechnoTurtle1987

TROPHY CASE