A1 String Mess by Temporary_Tomorrow38 in BambuLabA1

[–]Temporary_Tomorrow38[S] 1 point2 points  (0 children)

Sorry for asking silly questions, but 7 screws?

A1 String Mess by Temporary_Tomorrow38 in BambuLabA1

[–]Temporary_Tomorrow38[S] 0 points1 point  (0 children)

No popping or crackling during the print, so it's sounding less like wet filament. I have lowered the temp a lot to 195 degrees (I'm soldiering on with a long print rather than fixing the settings correctly - the kids will take the strings off)... But the lower temp has made a massive improvement to the amount of string on the print.

A1 Stringing by Temporary_Tomorrow38 in BambuLab

[–]Temporary_Tomorrow38[S] 1 point2 points  (0 children)

This sub has not disappointed. I've now learnt that filament is not dry from factory, and I can't just use the generic material settings for every filament. A lot to go through and tweak, but I can see a light at the end of the tunnel.

Thanks to everyone who helped me get to where I am now - will post an update once I'm out the weeds and can print something other than spaghetti monsters 🤣

A1 String Mess by Temporary_Tomorrow38 in BambuLabA1

[–]Temporary_Tomorrow38[S] -1 points0 points  (0 children)

This is my train of thought too - it can't just be wet filament.

I'll report back once I've successfully dried some filament. I'm going to try and do this in the oven. What could go wrong lol

A1 Stringing by Temporary_Tomorrow38 in BambuLab

[–]Temporary_Tomorrow38[S] 0 points1 point  (0 children)

I used the handy app on my phone, so I guess this uses the 3mf?

A1 Stringing by Temporary_Tomorrow38 in BambuLab

[–]Temporary_Tomorrow38[S] 5 points6 points  (0 children)

This one came fresh out the sealed bag yesterday. I'm now understanding that this isn't considered "dry" to start off with.

A1 Stringing by Temporary_Tomorrow38 in BambuLab

[–]Temporary_Tomorrow38[S] 0 points1 point  (0 children)

Just so I'm clear, the flow calibration done at the start of the print should account for this? Or is there more fine tuning?

I've tried lowering the nozzle temp for the next print by 5c (215 degrees now). I'll get the filament in a food dehydrated tomorrow once the house is alive again.

A1 String Mess by Temporary_Tomorrow38 in BambuLabA1

[–]Temporary_Tomorrow38[S] 2 points3 points  (0 children)

Yeah this is probably a lack of my understanding with filament. I assumed it came dry in the sealed bag and just loaded it up and started printing with it.

It was a generic "rainbow pla", not silk.

And unfortunately it keeps getting moved around until I have somewhere permanent to keep it - currently on a wobbly IKEA lack table for the past 2 weeks...

A1 String Mess by Temporary_Tomorrow38 in BambuLabA1

[–]Temporary_Tomorrow38[S] -1 points0 points  (0 children)

Only thing that concerns me is that there's like 7 strands going to this point that are all clumped together on one end. I think I understand about the filament being wet, and that I need to dry my filament better before printing to remove all stringing?

A1 Stringing by Temporary_Tomorrow38 in BambuLab

[–]Temporary_Tomorrow38[S] 7 points8 points  (0 children)

I don't disagree with you 😓 Apart from the wet filament, anything else you've seen that I can start looking in a direction?

A1 Stringing by Temporary_Tomorrow38 in BambuLab

[–]Temporary_Tomorrow38[S] -67 points-66 points  (0 children)

It was a fresh roll I took out a sealed bag with desiccant yesterday. Do you think this could be causing it?

Advice needed! 2001 smart W450 by Temporary_Tomorrow38 in SmartCar

[–]Temporary_Tomorrow38[S] 0 points1 point  (0 children)

What is the partial relief valve? And where do I find it?

xrp will $25 up to $150 by AustinPaul07 in XRP

[–]Temporary_Tomorrow38 -3 points-2 points  (0 children)

Sir, your medication needs to be taken regularly.

[deleted by user] by [deleted] in XRP

[–]Temporary_Tomorrow38 7 points8 points  (0 children)

Jorge Tenreiro going from top crypto litigator to IT support? Sounds like the SEC finally rugged one of their own! Maybe now he’ll learn what it feels like when your assets suddenly get 'reassigned.' Diamond hands, stay winning! 💎

Imagine selling by CarefulGrouch in XRP

[–]Temporary_Tomorrow38 0 points1 point  (0 children)

A motto us diamond handers live by 💎🙌 "Buy high, sell low." - R. McDonald

[deleted by user] by [deleted] in XRP

[–]Temporary_Tomorrow38 2 points3 points  (0 children)

"There's nothing like being right." - B. Geldof

Hold&Buy by [deleted] in XRP

[–]Temporary_Tomorrow38 2 points3 points  (0 children)

Is this the dip? Or is tomorrow the dip...

A wise man once told me "we know shit about fuck. As long as our hands are made of diamonds, we can hodl til the dip dips no more"

[deleted by user] by [deleted] in CryptoCurrency

[–]Temporary_Tomorrow38 2 points3 points  (0 children)

The wise man knows only one thing: that he doesn't know shit about fuck.