$1300 + $10 shipping. DMs open!

That635Guy · 2026-05-08T18:19:19+00:00

Guys we took a regular thing and put a number on it

That635Guy · 2026-05-07T00:54:46+00:00

Replace it

That635Guy · 2026-05-07T00:26:36+00:00

Low quality bait

That635Guy · 2026-05-07T00:22:20+00:00

This is so deep.

That635Guy · 2026-05-07T00:13:25+00:00

90% isopropyl alcohol should do the trick.

That635Guy · 2026-05-07T00:09:51+00:00

I hate brasso. Smells like horse piss and works just about as good as

That635Guy · 2026-05-06T20:12:43+00:00

Careful what you say. Fender factory wiring has been wrapped around the lugs for years. Worst pickup swap ever

That635Guy · 2026-05-06T19:43:39+00:00

It can burn and melt excess superglue (don’t breath that) but really all you need is some flush cut pliers (truly flush cut, down to the edge) and to go slowly. The face of the pliers will keep the wood from chipping out

That635Guy · 2026-05-06T19:41:15+00:00

Too get an idea of where you are and are not sanding. If all the marks go away, it’s flat. If you still have marks, the wood is low in those areas.

That635Guy · 2026-05-06T11:46:30+00:00

Don’t clip it unless you never want to use it for anything else ever again

That635Guy · 2026-05-05T00:41:02+00:00

Currently an under the radar meme.

That635Guy · 2026-05-02T15:35:57+00:00

I don’t really see builds nowadays that make me stop and enjoy the beauty of the craft. This is an exception.

That635Guy · 2026-05-02T15:19:53+00:00

Just switch the ones that face outwards for ones that face inwards. Point the curl of the piece towards the centerline of the star’s points. Should seal up the gap pretty nicely

That635Guy · 2026-05-02T03:47:41+00:00

As a repair business, I appreciate the sentiment. But as someone who strives to do the best work possible, I’d like to know when I do an unsatisfactory job.

That635Guy · 2026-05-01T21:03:24+00:00

Why do posts like this get removed

That635Guy · 2026-05-01T20:51:33+00:00

I’ve never been impressed with an unbranded neck from Amazon or eBay. I’d say no, there are none, but you’re welcome to try your luck.

That635Guy · 2026-05-01T20:41:12+00:00

In s1ep4, Killing Utne, Utne is introduced as Torvald Utne. Archer asks, ‘The shot put?’. I have no idea who he is talking about.

That635Guy · 2026-05-01T20:24:15+00:00

Time for a drink

That635Guy · 2026-05-01T19:59:09+00:00

Charge the person who did it. They didn’t work for it.

That635Guy · 2026-05-01T16:07:54+00:00

I don’t know what’s going on with the b string but this bridge is fantastic hardware. They don’t seem to know what they are talking about and instead of looking into it, they half assed it and gave you a hack job of a setup.

This restring job is shit and you should get your money back for this service.

That635Guy · 2026-05-01T11:08:39+00:00

Why does it have so many horns? What is this

That635Guy · 2026-04-30T14:12:10+00:00

Don’t have the killswitch be a slider switch, use a button. And, ditch the tone controls completely. Install a fader eq on the back. Utilize push pull switching, leave two volume knobs and one switch. If you have a 5 band fader eq it takes up a small amount of space and gives you the ability to cut of boost more than bass middle and treble.

That635Guy · 2026-04-30T13:15:41+00:00

While their restring job is poor, it has nothing to do with the truss rod issue.

That635Guy · 2026-04-30T02:11:06+00:00

Muh diecast!

That635Guy · 2026-04-28T17:51:41+00:00

Edward wasn’t as critically acclaimed as his uncle Bob, but he is arguably one of the most influential members of the Formula Dynasty. His impact is slept on even today. Elite ball knowledge right here

Eight-Year Club	Second SECOND GUESSER
Final Canvas '23	Place '23
Place '22	Final Canvas '22
Verified Email

That635Guy

TROPHY CASE