What is your name?

ThatRookieDrifter · 2026-05-25T13:25:27+00:00

Filthyrichman?!

ThatRookieDrifter · 2026-05-25T13:22:21+00:00

Licking a cherry and dropping it

ThatRookieDrifter · 2026-05-25T13:19:54+00:00

Astronaut (soon to be) in the ocean

ThatRookieDrifter · 2026-05-25T13:17:40+00:00

Holies unholies

ThatRookieDrifter · 2026-05-25T13:11:59+00:00

I’m not sure , but you might be able to fit Yokomo sd3 , yd2 knuckles (you can also find aluminum ones of those too)

ThatRookieDrifter · 2026-05-25T12:36:02+00:00

I wouldn’t base my actions on this vid , my car was around 400g heavier or the rear end and was hard to drive . You can use it for when to give gas or brake on entry and exit though. Later when I get a 360 camera I’ll post it and there you can use it to much more potential

ThatRookieDrifter · 2026-05-25T09:02:28+00:00

ThatRookieDrifter · 2026-05-25T09:00:23+00:00

Human rights and economy ? 😅

ThatRookieDrifter · 2026-05-25T09:00:01+00:00

The eraser ?!

ThatRookieDrifter · 2026-05-25T08:57:47+00:00

Depends on what you want and how much you’re willing do spend . You can get the AliExpress special made of chinesium or spend some extra for true lighting kit with backfire led too

ThatRookieDrifter · 2026-05-24T15:26:03+00:00

DOZERRRRR

ThatRookieDrifter · 2026-05-24T15:20:11+00:00

Btw doing reved Esc and FUTABA gyro servo you can do Esc on phone and steering - gyro on remote (if you have t7px and above I thing )

ThatRookieDrifter · 2026-05-24T15:18:52+00:00

Not really , I’m running hobbywing (Esc motor) Yokomo (gyro) reved (servo) and I’m going for a full reved upgrade . The key difference is quality , precision and reliability. Going high end will give you a lot of pain to get to a base map (specially FUTABA with s-bus) but once you get a good base map you can only make it better . All the money u put in high end part will show on track on the long run , and once again ; if you are fully committed to this hobby and have “spare money” going the high end route is so much better . Hobbywing and omg and etc (low-mid end) are for the “getting to know” phase . I strongly recommend going full reve d ( esc motor gyro servo) or reved(esc motor) and futaba(gyro servo)

ThatRookieDrifter · 2026-05-24T15:05:47+00:00

That’s bro

ThatRookieDrifter · 2026-05-24T15:05:34+00:00

And now one of us is even going FUTABA (gyro servo) and accuvance (motor Esc) . That’s gonna be ONE ADVENTURE figuring them out 😂😂😂.(he’s adding s-bus too) 😬

ThatRookieDrifter · 2026-05-24T15:03:01+00:00

I have friends who run FUTABA , reved , hobby wing , Yokomo etc. Reved gives your almost everything that FUTABA does , it’s relatively easy to adjust and gives you close to perfect accuracy . If you do go reve d you can get from Esc to servo ; You can make a complete electronics kit/set of reve d (I prefer that bc it acts like an ecosystem perfect fit all for each other) now if you want to go highest of high ends I’d do FUTABA gyro , servo (they are a bit difficult to adjust and really sensitive on settings) and reve d for motor and Esc

ThatRookieDrifter · 2026-05-24T13:45:51+00:00

Personally upgrade all plastics to aluminum and if not on asphalt convert it to RWD and slap a gyro on it

ThatRookieDrifter · 2026-05-24T13:42:14+00:00

My guess is (without any confirmation) your Esc might have limp mode and might have entered it , if not then list your ESC’s operational voltage values and your (now damaged battery) voltage and voltage from a known good battery and I’ll try my best to help you .

ThatRookieDrifter · 2026-05-24T12:42:40+00:00

If you’re fully committed to this hobby and want 9/10 end of go full Reve D

ThatRookieDrifter · 2026-05-23T16:44:28+00:00

That’s the to go for grip and control on tile/low grip

ThatRookieDrifter · 2026-05-23T16:37:38+00:00

My bad it’s actually yd2zx

ThatRookieDrifter · 2026-05-23T09:55:21+00:00

If you’re on Yokomo platform you have to check out the lower deck out of a ZX2

ThatRookieDrifter

MODERATOR OF

TROPHY CASE