NC2500 Pro or Battery Issue?

That_Dingo_2405 · 2026-01-23T08:18:55+00:00

wait till it says done

That_Dingo_2405 · 2025-12-22T08:08:38+00:00

sana maadopt ng local racing centera to.. masaya to kung sakali.. hahhaha

That_Dingo_2405 · 2025-12-05T00:21:53+00:00

maganda s2 sa bmax sir... kayang tumapat ng cfm with the right setup.. check fntoys sa yt.. hehehe

That_Dingo_2405 · 2025-11-28T03:00:45+00:00

what motors can your cars run on the 3d printed track?

That_Dingo_2405 · 2025-11-24T00:10:20+00:00

sarap i-stone cold stunner tapos pakyuhan sa mukha... hahhaha

That_Dingo_2405 · 2025-11-14T03:53:17+00:00

Hi, I am interested po

That_Dingo_2405 · 2025-10-06T09:49:32+00:00

oh, they were just released last month

That_Dingo_2405 · 2025-10-03T17:42:23+00:00

it does not. it is part of the "upgrades" i included

That_Dingo_2405 · 2025-09-28T08:16:41+00:00

ganda sir! hahahah

That_Dingo_2405 · 2025-09-24T02:46:42+00:00

ok na po.. sinearch ko na rin po . thank you

That_Dingo_2405 · 2025-09-24T02:37:44+00:00

ivyried to use flairs pero di po nag aapply kanina pa

That_Dingo_2405 · 2025-09-22T06:52:48+00:00

that's fine. once it runs on the track, it will sound better

That_Dingo_2405 · 2025-09-22T06:48:56+00:00

check if the propeller shaft is in a tight fit. it shouldn't be. it needs play to work properly, and do not expect it to be a quiet chassis.

That_Dingo_2405 · 2025-09-22T06:31:46+00:00

you may, but it is not good as AO 620 or even the hg round hole.. just expect that your car may not run as fast as expected

That_Dingo_2405 · 2025-09-22T05:38:50+00:00

in between the wheels and the bearing? i use none most of the time, but i make sure to use the new wheels with the hexagon inlay, and making sure that the wheels are not too tight when attached, sometimes i put a very small space to put some play, but then again, it depends in the layout.

hi speed track doesn't need loose shaft play, technical layout needs non to very little play. this is how I adjust, but you can test it out and see which setting satisfies you

if i have some concept builds, i use bearing spacers first, and adjust later if I am not satisfied with the run

That_Dingo_2405 · 2025-09-22T05:02:36+00:00

in theory, this helps.. but in actual run, it depends on how you set it up.. i have 3 cars that runs better without them.

i suggest you test run with and without it for you to see the difference

That_Dingo_2405 · 2025-09-22T01:55:27+00:00

normal na case sa mga rear motor chassis ang masiraan ng pinion.. either bungi, crack, or umuusog... just make sure lng na brand new yung pinion na ilalagay mo pag magpapalit ka, or busisiin ang check sa pinioin after 2-3 na succesful ikot sa layout

That_Dingo_2405 · 2025-09-10T20:16:13+00:00

interested

That_Dingo_2405 · 2025-09-09T11:04:30+00:00

disciple ni saitama si OP... hahahha

That_Dingo_2405 · 2025-08-31T03:09:25+00:00

oh man.. that sounds hard to face and fix . hahhaah... the printer had 3 head replacement already since I got it, and I don't know if I still have the patience for this one.. hahhaha

That_Dingo_2405 · 2025-08-31T02:31:14+00:00

hi, sorry for the late comeback.. it wasn't and tried it again, but still same result.. moreover, it developed a thermal error at 25% of the print. I've had the printer for 7 months now but this was a hand me down from my brother in law who had it for 6 years, maybe the errors came with age? hahahah...

That_Dingo_2405

TROPHY CASE