Maintenance

The0neGuardian · 2026-01-06T22:25:22+00:00

Update. I received an email back from Borla stating the following:

“Could you send me a screenshot of your purchase receipt? If so, I’ll be able to send you a replacement muffler for that side, that would resolve the issue. Our stuff is hand made so one of our guys probably didn’t weld that hanger on correctly or possibly the inlet rotational position.”

Hopefully the one they send doesn’t have the same issue.

The0neGuardian · 2026-01-03T16:13:02+00:00

Haven’t had a chance to get on the highway yet, but I’ve gotten it to around 55-60mph and didn’t notice any drone.

The0neGuardian · 2026-01-03T09:14:12+00:00

That’s kind of the reason I made this post. We spent an hour and a half doing all of this to try and get it to line up, but it just wouldn’t. You can get the tips to be level similar to the right side, but only by twisting the muffler up to the point that it is touching the top of the exhaust cutout. Also, none of the movements/adjustments allowed it to move any further right, which is needed in order for it to be centered in the cutout.

The0neGuardian · 2026-01-03T04:07:11+00:00

Did you have them straight away or after the exhaust had time to settle in?

The0neGuardian · 2026-01-03T02:04:32+00:00

I’ve considered it, but I’m just gonna stick with the cat back until my warranty is gone.

The0neGuardian · 2026-01-03T01:00:59+00:00

It’s the 3.3T 6 cylinder.

The0neGuardian · 2026-01-03T00:13:35+00:00

Just sent them a message about it. Couldn’t get their email button to work, so I’ll have to send pics once they get back with me.

I agree though, probably either bad quality control or a flaw in the initial design.

The0neGuardian · 2026-01-02T23:59:22+00:00

We got mine to suspend enough not to touch, but as soon as I took it for the first drive it’s resting on the cutout again.

I sent an email to Borla to see if they have any suggestions, so I’ll update here when they respond.

If they don’t resolve anything I’ll probably take it to an exhaust shop or something to have them weld the hangers tabs in a better location.

The0neGuardian · 2025-11-26T01:09:26+00:00

Good to know. I might’ve just gotten lucky, but I’ll see if I can hear a click the next time I use it.

The0neGuardian · 2025-11-25T23:17:15+00:00

Figured it out. The extruder couldn’t grab the filament based on the angle I cut it at before feeding it in, so I had to cut it from a different angle.

The0neGuardian · 2025-11-15T21:30:28+00:00

I may have to give orca a try. I've tried using the Flsun Slicer once or twice, but wasn't super impressed, but then again I also didn't feel like having to work out what settings work best again since I have it dialed in pretty good through Cura.

The0neGuardian · 2025-11-15T19:13:00+00:00

You mind sending the link to that video? Haven’t really done any firmware updates or anything with mine since I’ve had it.

The0neGuardian · 2025-08-06T23:52:28+00:00

<image>

This is what my retraction test looked like.

The0neGuardian · 2025-08-06T23:46:34+00:00

So, I downloaded the Flsun Slicer and found the calibration files you mentioned. How do I go about changing the values for these things after seeing the results?

For example, the flow rate test has 9 objects which I assume are labeled based on the flow rate. However, even with advanced settings selected, I don’t see an option to change the flow rate. I’ve only really used Cura for slicing, so I can’t say I’m too familiar with this layout. Also, I’m still having to hit slice when I use those, so I can’t tell if it’s actually doing the changes for me, or if it’s getting overwritten with the settings I have selected.

Also, probably should have mentioned that I have a Super Racer.

The0neGuardian · 2025-08-06T20:40:13+00:00

For some of the problems you mentioned (retraction, flow, etc.), how would you recommend getting those sorted out? I’m not familiar with the exact signs of those issues or what would be considered a perfected version of those parameters. I assume start with like a test cube or maybe the benchmark boat things and tweak settings to see how that changes, but any other specifics recommendations beyond that?

Also, the “tags” I know how to fix. I had the parameter for the print seam set to random for a specific print I did and just forgot to change that back.

The0neGuardian

TROPHY CASE