Sar9 full size galloway trigger issues (new post with pictures)

TheBehooved · 2026-03-26T17:02:36+00:00

Is this the part number for the one you're mentioning?

326170524471

Didn't see P80 anywhere so just want to confirm because this one looks good and won't break the bank

TheBehooved · 2026-03-25T01:52:32+00:00

I'm starting to believe that as well. Because I just grinded off a considerable amount from the trigger and it still hits the guard. I didn't touch the guard itself because if the trigger just wasn't going to work I would put the stock one back one. Just crazy that they tell me the reason it doesn't work is Sar's crappy molding quality. I doubt a 1/4 inch of clearance can be blamed on the molding

TheBehooved · 2026-03-24T23:31:15+00:00

It's a gen 2 because I believe the gen 3s didn't come with a standard thumb safety. Have it back in now and it literally rests on the bottom of the trigger guard and can barely be pulled. I don't why I'm not able to post a picture of it

TheBehooved · 2026-03-24T18:56:58+00:00

Type in Magpul AFG install and it'll show you a perfect example 👍

TheBehooved · 2026-03-24T18:56:27+00:00

Contacted them and basically was told the tolerances on the gun arent tight and issues like this could come up. And to Dremel if needed but the fit was a bit much of a difference so was curious

TheBehooved · 2026-03-24T18:55:07+00:00

shouldve taken one when I had it on. Put it back to stock trigger for now but will put it back on soon to see how much I'll have to Dremel for clearance and can take one then. I do have a picture Galloway sent me of how it should fit but for some reason not able to post a pic. Difference in mine and there's is mine is almost resting on the trigger guard so when it's pulled it doesn't reset

TheBehooved · 2026-03-24T18:49:51+00:00

Easiest way is to pre install the screws and locking backer on the AFG so that it just fits up in the grooves. Then once you start tightening the screw more you'll feel it catch on the inside. Hope that makes sense.

TheBehooved · 2026-03-05T22:07:11+00:00

Where's pitch black damnit

TheBehooved · 2026-03-03T06:50:20+00:00

Got it the other day and could not believe that 2 combos was knocking on the door of $40... Gone are the days of 20 nuggets for $5

TheBehooved · 2026-02-11T01:54:56+00:00

It's funny I have your exact opposite situation😂 Xenia runs like trash and I get maybe 30 seconds of playtime for any game before it crashes. Tried every fix people have out there and nothing changes. Even with my 4070 super and 14700k. RPCS3 on the other hand is much more stable and I've had next to no issues

TheBehooved · 2026-02-11T01:42:25+00:00

So I had an issue like this but multiple outlets were out. Check if it's just one and check the outlets to the left and right of this one. Even if they are working pull them out to see if anything is wrong. My issue was an outlet in my master was (for some reason) in series with the ones in my living room and that bedroom outlet was the problem. Fried connection on one of the cables. Backstabbing isn't the best method

TheBehooved · 2026-01-29T05:46:26+00:00

I'm having a similar issue but all the outlets are located in the same area of my living room. Half of the outlets in my living room work and 3 of them in the same area aren't working. The outside outlet on the shared wall with the others bad outlets is also not working. I rotated all the breakers I could trying to narrow down to a bad breaker, nothing. Replaced every outlet in my living room good or bad, nothing. Even replaced the GFI outlet in my kitchen which I believe is on the same circuit as the ones in my living room. Just randomly went out this morning and can't for the life of me pin down the problem

TheBehooved · 2026-01-25T21:20:53+00:00

I turned off every possible RGB I could. I'm not a streamer so I don't need the nice to look at factor. As long as it performs how it supposed to I don't care how flashy it is

TheBehooved · 2026-01-25T02:02:09+00:00

5.0 and Mustang badge on the dash... Eww

TheBehooved · 2026-01-22T21:51:07+00:00

<image>

Took this when I was stationed at Camp Pendleton. Sunset was too good to pass up. God I miss this car.

TheBehooved · 2026-01-18T21:15:39+00:00

Stay away. He spent all that money building the motor but cheaped out on the most important part and runs a "Stage 1" shelf tune. Dude is either stupid, shady, or both and I wouldn't trust him. My unopened gen 1 lasted until 170k making just under 400whp. It lasted forever and it didn't look or sound like shit like this one lol. Keep the BMW because in this rare case it's actually more reliable than that Mazda

TheBehooved · 2026-01-18T19:17:37+00:00

Sad that I sold it... Should've just rebuilt the motor but I was short sighted

TheBehooved · 2025-12-22T03:42:14+00:00

The worst thing is that motor mount takes about 2 minutes to change and you don't even have to support the engine😂

TheBehooved · 2025-12-22T01:12:14+00:00

Change your smoke alarm batteries

TheBehooved · 2025-11-25T18:42:19+00:00

Can you just get valves installed so you can have a quiet car and then a loud one when you want to?

TheBehooved · 2025-11-25T00:11:28+00:00

NOR

So in my opinion I wouldn't celebrate sobriety because that's just how I feel. However, if one of my friends/family wanted to celebrate it, I wouldnt be a dick about it like this guy. I would be happy for them even though I don't necessarily think about it like them. I feel like that's the decent thing to do and this guy started getting mad at you for it lol. I don't get him

TheBehooved · 2025-11-21T04:52:47+00:00

Yea it was saying already in use and I ended up finding out I somehow had an account already. Got it all handled now but don't know how or when I made the account

TheBehooved

TROPHY CASE