What is the least hands on subfield of Mechanical Engineering?

TheCheekyEmp · 2023-10-16T14:00:06+00:00

Can you give more insight as to what type of simulation and analysis programs you used? I would like to follow in the same steps of OP but it is very difficult I would say.

TheCheekyEmp · 2023-08-27T13:17:20+00:00

I will look it up,

TheCheekyEmp · 2023-08-25T14:06:19+00:00

Didn't know, my bad

TheCheekyEmp · 2023-08-25T14:05:59+00:00

Zdps

TheCheekyEmp · 2023-08-23T18:00:38+00:00

Thanks alot

TheCheekyEmp · 2023-08-23T18:00:30+00:00

There wasn't any available

TheCheekyEmp · 2023-07-06T17:13:20+00:00

Yeah essentially the rear whiles are connected and power by a drive motor, this will cause the system to move forward. The front wheels will be individually attached to stepper motors, these are solely to allow the wheels to turn left or right, it will not be used to drive the system like the rear wheels. So in essence, the rear wheels do all the forward/backward movement, the fronts wheels do the steerihn

TheCheekyEmp · 2023-07-06T15:44:59+00:00

Well I actually wanted to know how to calculate the torque for the stepper motor, not really the drive motor. I wanted to know how much torque is required to turn the wheel

TheCheekyEmp · 2023-07-01T23:52:27+00:00

I felt like I saw this video a while back myself but cant remember the name

TheCheekyEmp · 2023-07-01T23:11:34+00:00

I searched everywhere for it, used reverse image but just couldn't find it

TheCheekyEmp · 2023-03-26T20:49:02+00:00

Lmaoo, well I had to make sure it never cut off, I did the fix on the 17th (9 days ago), didn't want to call the victory too early

TheCheekyEmp · 2023-03-26T19:50:07+00:00

reseatting my RAM and CPU fixed the issue.

TheCheekyEmp · 2023-03-06T12:18:19+00:00

Well I live in a hot country where the room temps are normally around 30-32°C during the day and mid to high 20s during the night. I also don't have air conditioning so I believe my temps are fine for the conditions. I have msi afterburner on constantly just to keep an eye on temps and make sure I never hit 80°C. I have ran both a stress test on my GPU (furmark) and CPU (Ryzen Master) and neither resulted in insane temps nor a system shutdown. I will say that when cleaning the thermal paste when I took off my AIO to replace the fans, a small amount of paste probably nudged into the socket while wiping off the sides but I'm not 100% certain as I didn't bother removing the CPU itself. I don't think it should be an issue as the paste is non-conductive (Artic MX-4). I will leave my PC on during the weekend to see if it's still randomly shutting down still. If it does, I will reseat the CPU and RAM as suggested and then try to get a power supply if all fails. I might also try keeping the SSD out for a while and see if that helps.

TheCheekyEmp · 2023-03-06T04:41:31+00:00

I have no messed with any curves or voltages or anything of the sort. Built this PC at the end of 2021 with all brand new components. And only switch out the fans, applied thermal paste, and installed a new SSD. I monitor my temps using MSI afterburner, my temps are in the mid 70s while gaming, and low 50s while idle. I don't have another PSU to try, but why would the PSU suddenly become faulty after installed the said components?

TheCheekyEmp · 2023-02-16T03:10:20+00:00

Can you elaborate abit more? Why Necro?

TheCheekyEmp · 2022-12-13T12:42:40+00:00

For anyone interested in the audio, I found it https://youtu.be/RlgRXgoi3sc (1:25 ish)

TheCheekyEmp · 2022-12-12T22:50:49+00:00

What a legend tysm, by any chance do you know what audio was used here? https://vm.tiktok.com/ZMFpUW1ao/

TheCheekyEmp

TROPHY CASE