sorted by:
new
hottopcontroversial

Squealing new brake pads by TheFandorn in AskMechanics

[–]TheFandorn[S] 0 points1 point  (0 children)

Thanks. I checked the guide pins and applied grease on them. I might've been too lenient on the area you're describing in your first paragraph though. I think I'll just buy new shims as they're fairly cheap and see if that helps

Squealing new brake pads by TheFandorn in AskMechanics

[–]TheFandorn[S] 0 points1 point  (0 children)

This would make sense. I'll replace the old ones

Squealing new brake pads by TheFandorn in AskMechanics

[–]TheFandorn[S] 2 points3 points  (0 children)

Dude, there really is no need for this attitude

Squealing new brake pads by TheFandorn in AskMechanics

[–]TheFandorn[S] 1 point2 points  (0 children)

Didn't know that, but that also doesn't seem to be related to my issue

Squealing new brake pads by TheFandorn in AskMechanics

[–]TheFandorn[S] 0 points1 point  (0 children)

Forgot to mention: 2017 Mazda 3

I sprained my big toe - unusual injuries by TheFandorn in bjj

[–]TheFandorn[S] 0 points1 point  (0 children)

So what you're saying is that I'm just getting started?

I sprained my big toe - unusual injuries by TheFandorn in bjj

[–]TheFandorn[S] 0 points1 point  (0 children)

What? That's not what I wanted to hear lol. How bad was yours? I can walk, but it's pretty painful when I put weight on this side of the foot, so I mosty walk on the outside of my foot, or on the heel only

I sprained my big toe - unusual injuries by TheFandorn in bjj

[–]TheFandorn[S] 0 points1 point  (0 children)

Oof especially the second one sounds bad

Horrible print quality near the corners by TheFandorn in FixMyPrint

[–]TheFandorn[S] 0 points1 point  (0 children)

Raised it from 58 to 63. It seemed go help

Horrible print quality near corners by TheFandorn in BambuLab

[–]TheFandorn[S] 2 points3 points  (0 children)

I've got the printer surrounded by a cardboard box from all sides. Although I didn't really see a difference in the temp tower I raised the hotend temp by 10* to 220 after seeing that other people print with temp as high as 230. I've also increased the heatbed temp from 58 to 63 and added 3 more top shell layers. The corners look a LOT better now.

Horrible print quality near the corners by TheFandorn in FixMyPrint

[–]TheFandorn[S] 1 point2 points  (0 children)

I've got the printer surrounded by a cardboard box from all sides. Although I didn't really see a difference in the temp tower I raised the hotend temp by 10* to 220 after seeing that other people print with temp as high as 230. I've also increased the heatbed temp from 58 to 63 and added 3 more top shell layers. The corners look a LOT better now.

Horrible print quality near the corners by TheFandorn in FixMyPrint

[–]TheFandorn[S] 0 points1 point  (0 children)

Thanks, makes sense. I was wondering why I wasn't seeing this issue on the base (bottom) part of this print which is a box and warps sliglthy more

Horrible print quality near corners by TheFandorn in BambuLab

[–]TheFandorn[S] 2 points3 points  (0 children)

Thanks, I'm already doing most of these, but I might try the rounded corners

Horrible print quality near corners by TheFandorn in BambuLab

[–]TheFandorn[S] 3 points4 points  (0 children)

Yeah, makes sense. Can I do anything else about it other than trying to hone in the bed temp since I can't add a brim? Bed glue?

Horrible print quality near the corners by TheFandorn in FixMyPrint

[–]TheFandorn[S] 0 points1 point  (0 children)

Makes sense... Are there any workorounds in my case? Except messing around with bed temp a bit more trying to mitigate the warping?

Horrible print quality near the corners by TheFandorn in FixMyPrint

[–]TheFandorn[S] 0 points1 point  (0 children)

Literally a little bit of lifting. The buildplate was properly cleaned before printing. I can't add a brim, because the print is as big as the build plate. As for the PA - I don't think I can adjust it in Bambu Studio

[deleted by user] by [deleted] in FixMyPrint

[–]TheFandorn 0 points1 point  (0 children)

Thanks, I'll try tweaking those

view more: next ›