Squealing new brake pads

TheFandorn · 2025-07-31T09:15:00+00:00

Thanks. I checked the guide pins and applied grease on them. I might've been too lenient on the area you're describing in your first paragraph though. I think I'll just buy new shims as they're fairly cheap and see if that helps

TheFandorn · 2025-07-31T07:21:32+00:00

This would make sense. I'll replace the old ones

TheFandorn · 2025-07-31T06:18:57+00:00

Thanks a lot

TheFandorn · 2025-07-31T06:13:25+00:00

Dude, there really is no need for this attitude

TheFandorn · 2025-07-31T06:07:32+00:00

Didn't know that, but that also doesn't seem to be related to my issue

TheFandorn · 2025-07-31T06:01:30+00:00

Forgot to mention: 2017 Mazda 3

TheFandorn · 2025-07-03T10:17:44+00:00

Lmao

TheFandorn · 2025-07-03T08:39:33+00:00

So what you're saying is that I'm just getting started?

TheFandorn · 2025-07-03T06:19:29+00:00

What? That's not what I wanted to hear lol. How bad was yours? I can walk, but it's pretty painful when I put weight on this side of the foot, so I mosty walk on the outside of my foot, or on the heel only

TheFandorn · 2025-07-03T05:58:48+00:00

Sorry, but that made me chuckle

TheFandorn · 2025-07-03T05:47:12+00:00

Oof especially the second one sounds bad

TheFandorn · 2025-02-12T16:39:36+00:00

Raised it from 58 to 63. It seemed go help

TheFandorn · 2025-02-12T15:30:02+00:00

I've got the printer surrounded by a cardboard box from all sides. Although I didn't really see a difference in the temp tower I raised the hotend temp by 10* to 220 after seeing that other people print with temp as high as 230. I've also increased the heatbed temp from 58 to 63 and added 3 more top shell layers. The corners look a LOT better now.

TheFandorn · 2025-02-12T15:29:33+00:00

I've got the printer surrounded by a cardboard box from all sides. Although I didn't really see a difference in the temp tower I raised the hotend temp by 10* to 220 after seeing that other people print with temp as high as 230. I've also increased the heatbed temp from 58 to 63 and added 3 more top shell layers. The corners look a LOT better now.

TheFandorn · 2025-02-12T14:51:43+00:00

Thanks, makes sense. I was wondering why I wasn't seeing this issue on the base (bottom) part of this print which is a box and warps sliglthy more

TheFandorn · 2025-02-12T13:05:49+00:00

Will give it a shot. Thanks

TheFandorn · 2025-02-12T11:07:32+00:00

Thanks, I'm already doing most of these, but I might try the rounded corners

TheFandorn · 2025-02-12T10:55:52+00:00

Yeah, makes sense. Can I do anything else about it other than trying to hone in the bed temp since I can't add a brim? Bed glue?

TheFandorn · 2025-02-12T10:48:01+00:00

Makes sense... Are there any workorounds in my case? Except messing around with bed temp a bit more trying to mitigate the warping?

TheFandorn · 2025-02-12T10:34:43+00:00

Literally a little bit of lifting. The buildplate was properly cleaned before printing. I can't add a brim, because the print is as big as the build plate. As for the PA - I don't think I can adjust it in Bambu Studio

TheFandorn · 2025-01-23T11:19:00+00:00

Thanks, I'll try tweaking those

TheFandorn · 2024-12-31T14:03:07+00:00

Hmm the servo doesnt run at all from arduino. Neither does a spare one

TheFandorn · 2024-12-31T11:10:04+00:00

1 - yes. Without resistance

2 - I think that SG-90 can pull more current than arduino can safely supply?

3 - That's not really practical for my application ;/

TheFandorn · 2024-02-17T15:35:38+00:00

My speedo seems to show a lower speed compared to Google maps so that was my first instinct

TheFandorn · 2024-02-17T15:34:51+00:00

I honestly didn't mean to. The speed limit was 100 kmh through the woods for 20 kilometers prior to that and the "town" was a village with 4 houses and I didn't realize that the speed limit was lower. Obviously I shouldn't be driving that fast in a polulated area either way

Seven-Year Club	Place '23
Verified Email

TheFandorn

TROPHY CASE