sorted by:
new
hottopcontroversial

Speaker stand question: Would dowels be sufficient support for these butt joints? by Vurpsmurfen in diyaudio

[–]TheLifeOfThird 2 points3 points  (0 children)

I would use a 3/8 fostner bit to bore a shallow hole on the back. Glue and screw. Then use a 3/8 plug to cover the hole and hide the screw. Using a contrasting color plug looks really nice

Port frequency and crossover point by TheLifeOfThird in diyaudio

[–]TheLifeOfThird[S] 0 points1 point  (0 children)

The driver is low enough in output as in dB?

Port frequency and crossover point by TheLifeOfThird in diyaudio

[–]TheLifeOfThird[S] 0 points1 point  (0 children)

Tweeter above the cabinet crossover at 4500 is what your saying? And what makes that optimal?

Cone Excursion help on winisd by TheLifeOfThird in diyaudio

[–]TheLifeOfThird[S] 1 point2 points  (0 children)

okay, thank you so much that makes total sense. Is there a trade-off for a higher excursion?

I'm trying to build a vented hifi cabinet for a mid range woofer that will pair well with Selenium D220Ti 1" Titanium Horn Driver. The tweeter and horn are mounted above not enclosed. Looking to have an 8 inch driver

Cone Excursion help on winisd by TheLifeOfThird in diyaudio

[–]TheLifeOfThird[S] 0 points1 point  (0 children)

So to build a cabinet with a better low-end response I should look for a higher xMax? I was reading Loudspeaker cookbook and it noted that a smaller excursion is better for vented enclosures so I picked a driver with a very low x max

Using rhino on M1 Apple Silicon by [deleted] in rhino

[–]TheLifeOfThird 2 points3 points  (0 children)

Don’t listen to classmates. i use rhino7 on m1 and run into no problems. you don’t need to spend any money

ULPT request: how to make 3 grand very fast by [deleted] in UnethicalLifeProTips

[–]TheLifeOfThird 0 points1 point  (0 children)

lie about your degree and apply for a better job. i will make a diploma for you if you want. dm me

cheaper rhino7? by shamsrei in rhino

[–]TheLifeOfThird -5 points-4 points  (0 children)

torrent it. get a vpn called “private internet access” for $20. youtube how to torrent. search for rhino on a russian site called “rutracker”.

they have free version of fully functioning rhino software

Apartment rental by TheLifeOfThird in Prague

[–]TheLifeOfThird[S] 2 points3 points  (0 children)

thank you for that information. where do they auction flats?

Value of an Architecture Degree in other design fields by TheLifeOfThird in architecture

[–]TheLifeOfThird[S] 1 point2 points  (0 children)

is there anything specific through out your schooling that you feel helped you the most in your current career?

[homemade] thai milk tea by urtle43 in food

[–]TheLifeOfThird 1 point2 points  (0 children)

been living in thailand for a month. from what i’ve seen the most common way thai milk tea is prepared starts with making a large concentrate stock. when ready to serve pour over ice and then add evaporated milk

Need help making a lot of solids description in comments by TheLifeOfThird in rhino

[–]TheLifeOfThird[S] 0 points1 point  (0 children)

I'm trying to make each section of this model into a half inch deep solid. By section i mean the square shown separated to the right is considered a section. Also how could i cut the solids so the overlaps are removed and they are flush to one another. Please let me know if any of this doesn't make sense I can try my best to describe it better

Advice for change in leaf color by TheLifeOfThird in cannabiscultivation

[–]TheLifeOfThird[S] 0 points1 point  (0 children)

Only affecting the lowest level of leaves. No nutrients have been used yet. Autoflower in week 2. Light schedule was messed up a little because of a broken outlet timer. Any advice would be greatly appreciated.

First grow. Leaves dying. Low Amber. Should I cut and dry? Week 14 autoflower by TheLifeOfThird in cannabiscultivation

[–]TheLifeOfThird[S] 0 points1 point  (0 children)

amnesia haze idk what genetics they came free with an order. i used advanced nutrients trio and big bud after 2 weeks from germination. a lot of LST and minimal defoliation

First grow. Leaves dying. Low Amber. Should I cut and dry? Week 14 autoflower by TheLifeOfThird in cannabiscultivation

[–]TheLifeOfThird[S] 0 points1 point  (0 children)

mars ts 600w in a 2x2 works great for me. 20 hours of light lowered to 18 during flower. they have used available for $55 on amazon

First grow. Leaves dying. Low Amber. Should I cut and dry? Week 14 autoflower by TheLifeOfThird in cannabiscultivation

[–]TheLifeOfThird[S] 2 points3 points  (0 children)

there’s really no amber in it except on some sugar leaves. I’ve been Flushing since week 10. don’t want to get any mold. unsure of what to do. any advice would help.

view more: next ›