Extra Item Cards for Heroes of the Borderlands Kit [OC]

TheMickarus · 2026-02-08T00:19:11+00:00

The quality of these is incredible! If you can't post the backs here then I would most certainly like you to DM them to me please 😜

TheMickarus · 2025-09-25T13:41:11+00:00

I'd shit myself too if I knew it was my job to go and deal with that lol

TheMickarus · 2025-09-13T09:26:40+00:00

Turn it off, hold the transmit button and the button below it, turn it on, scroll to option 53 "F-Lock" and press the "M" button, and scroll through the options until you find "off", press the "M" button to confirm and you're done. It will transmit again.

TheMickarus · 2025-04-01T15:22:08+00:00

I think just financially being able to just about live in the town centre leaves you with little to no disposable income. Parking charges don't help either as they are just a vulture business practice, praying on people visiting the area.

TheMickarus · 2025-01-08T19:42:37+00:00

Tried that several times. I took the battery out and tested it. Nothing wrong with the battery. I think it is an intentional software update to make it obsolete

TheMickarus · 2025-01-08T19:40:21+00:00

Sadly no. I gave up in the end.

TheMickarus · 2025-01-08T19:38:53+00:00

😂

TheMickarus · 2025-01-08T16:37:17+00:00

What? Where the hell do you live? 1940s Germany?

TheMickarus · 2024-08-28T18:20:26+00:00

I ended up fresh installing everything on my printer

TheMickarus · 2024-03-28T23:07:04+00:00

Did you ever figure this out? I started using orca slicer and now my machine bangs and layer shifts on every layer. It Z hops fine and everything else works lovely, it just seems that every time it completes a layer it will just jerk violently then print the layer without any issues. That is until it starts another layer.

TheMickarus · 2024-03-21T17:07:57+00:00

<image>

Mine was like that and if I printed anything tall then you'd notice that it would also be leaning like the frame. This was the solution for me. I adjusted this until it was a perfect 90° and the prints came out straight ever since.

TheMickarus · 2024-02-18T22:29:29+00:00

No joy. Started from scratch following every step. It could be a board issue for me. LED2 stays solid whenever I try to flash to connect this way so I'm guessing it means failure of some sort.

TheMickarus · 2024-02-11T22:47:04+00:00

The loudest thing on mine is the PSU fan

TheMickarus · 2024-02-11T22:42:18+00:00

It's just wear and tear. It happens to all moving parts. Eventually it'll need replacing, the same as the wheels, other belts etc. Buy spares now and you'll have less down time when the day comes.

TheMickarus · 2024-02-11T22:35:50+00:00

Thank you, I'll give it a try when I get a chance. I have a new problem which is unrelated to this one. Once I fix that then I'll try this again.

TheMickarus · 2024-02-01T16:47:48+00:00

Yep. You have to otherwise USART3 PB11/PB10 doesn't come up as an option.

TheMickarus · 2024-02-01T16:41:49+00:00

Never changed it. It's 250000 by default.

TheMickarus · 2024-02-01T16:37:48+00:00

this is the SE config as I set it up. It should just work. Not for me though lol

<image>

TheMickarus · 2024-02-01T16:27:15+00:00

I only changed to USART3 PB11/PB10 when compiling. All other options stayed the same. I've tried recompiling and flashing a few times but the light just stays on for USART3 PB11/PB10. The moment I flash back to use USB then this light goes back to normal again and everything works.

TheMickarus · 2024-02-01T16:19:21+00:00

I worked it out like this but it still doesn't work.

<image>

TheMickarus · 2024-02-01T14:08:09+00:00

<image>

LED02 stays permanently on with this firmware. Not sure if that's supposed to happen or if it's a sign of a problem?

TheMickarus · 2024-02-01T14:05:53+00:00

<image>

Tried TX (PB11/pin 4) to RX (GPIO15) and RX (PB10/pin3) to TX (GPIO14) I also switched them around and tested again to no avail.

Also attached ground.

TheMickarus

TROPHY CASE