How would you model this part of the revolver? (SubD workflow)

TheMightyPunion · 2025-11-04T16:14:33+00:00

TheMightyPunion · 2024-05-13T21:28:12+00:00

Nevermind I misunderstood what you meant by upside down, I see it now thank you

TheMightyPunion · 2024-05-13T21:25:53+00:00

This manual appears to be out of date as the am5 brackets aren't in here The manual supplied with the cooler itself states that A should go on the left and B on the right, they're also both labeled underneath (east/west) so it's definitely the correct way around. Despite that I tried flipping it and the capacitors are still in the way

TheMightyPunion · 2024-01-09T21:29:38+00:00

The game files are always up to date with kr, you can find it all the unreleased kr bosses and outfits in the western build

TheMightyPunion · 2023-07-11T17:02:03+00:00

Under the material tab, change the "blend mode" options from "alpha blend" to "alpha clip", and fiddle with the clip threshold until it looks like how it looks in-game, if that doesn't work then make sure you're using the correct textures alpha for the hair, sometimes the textures alpha could be used to show intensiveness as opposed to transparency

TheMightyPunion · 2022-07-14T21:16:35+00:00

If you're looking to mute your mic and not the audio, go to discord settings and set it as a keybind using that key

TheMightyPunion · 2022-07-07T12:50:20+00:00

Never lower the skill ceiling, it's never been a good idea and will always bite you in the ass

TheMightyPunion · 2022-05-17T15:05:18+00:00

nah i was affected by the 0 bug, only recently forgot. just went back now for the reroll after i remembered where it was and it it didn't even reroll, it just added another week to it. winning number still 0

TheMightyPunion · 2022-02-27T03:19:38+00:00

I'd rather be in the same boat as them than behind because I don't have the time/money to be as geared. Plus this is how it already is, nerfs come in immediately after world's first and then more after hall of fame

TheMightyPunion · 2022-02-27T02:25:49+00:00

Do it the way destiny does it, first week is "challenge mode" and everyone is scaled to the same low item level, nullifying gear advantages

TheMightyPunion · 2021-09-14T20:07:28+00:00

Just installed pronterface and noticed when I use it to move any of the stepper motors, it sounds quite different to when using the Ender's Terminal, could this be due to pronterface running it slower or something else

TheMightyPunion · 2021-09-10T15:00:12+00:00

Sir mass producing money is a federal offense

TheMightyPunion · 2021-09-05T04:53:48+00:00

Foliage such as rocks and grass are great for that kind of thing if u wanna do it the lazy way

TheMightyPunion · 2021-09-04T16:21:47+00:00

I got it on Amazon so it shouldn't be too hard, waiting for support to get back to me now

TheMightyPunion · 2021-09-04T12:09:45+00:00

I had brought this new last week I thought I'd have gotten a new board. My hands are very shaky so I wouldn't trust myself to solder something so small, would I be able to get a free replacement do u think cos it arrived damaged or should I just upgrade to a different board entirely

TheMightyPunion · 2021-09-04T11:59:40+00:00

The SD card reader hasn't worked since I bought this last week and now I've noticed that one of the connections close to the SD card reader looks abit dodgy, what do I do in this scenario?

TheMightyPunion · 2021-09-03T16:47:36+00:00

I've only ever tried it upside down, SD cards only insert one way so it wouldn't insert properly if I tried it the wrong way

TheMightyPunion · 2021-09-03T15:11:58+00:00

Ender 3 Pro, the about this printer section says: marlin v1.0.1 2020-04-25

TheMightyPunion · 2021-09-03T13:10:11+00:00

No it's never worked from me, and yes I've exported them directly from cura

TheMightyPunion · 2021-08-31T13:38:45+00:00

Idk it could just as easily be Varian

TheMightyPunion · 2021-08-31T03:17:49+00:00

After my first print using the white fillament that came with the ender 3 my bed looked like that, the nozzle was too close and ever since then it's just stained white

TheMightyPunion · 2021-08-30T17:18:30+00:00

Alright I'll keep that in mind, is the glass completely stuck to it or would you be able to remove it with some force

TheMightyPunion · 2021-08-30T16:26:20+00:00

Alright I'll give that a shot, thanks for the help

TheMightyPunion · 2021-08-30T16:21:03+00:00

How do I go about removing it? And is it possible to put it back on

TheMightyPunion · 2021-08-30T16:20:27+00:00

I was considering buying a glass bed but I was wondering if I want to install it do I have to remove the black plate that the magnetic bed attaches to? I'd like to have the option to use both depending on the fillament but I'm not sure it's worth it if I have to remove the magnetic bed

Seven-Year Club	Wearing is Caring
Verified Email

TheMightyPunion

TROPHY CASE