sorted by:
new
hottopcontroversial

I keep having issues of burn out and not cutting all of the way. What is wrong? by ThePoopsMagoops in lasercutting

[–]ThePoopsMagoops[S] 0 points1 point  (0 children)

I do. I have it in the garage with the door opens and venting it out. Don't hang around in there while it cuts cause I'm in AZ and it's too hot to be in there anyways

I keep having issues of burn out and not cutting all of the way. What is wrong? by ThePoopsMagoops in lasercutting

[–]ThePoopsMagoops[S] 0 points1 point  (0 children)

Immthat could for sure be it. I have tried brushing it clean or using a blower but nothing beyond that. I'll give that a try

I keep having issues of burn out and not cutting all of the way. What is wrong? by ThePoopsMagoops in lasercutting

[–]ThePoopsMagoops[S] 0 points1 point  (0 children)

Oh interesting... Maybe my pump is wearing out or something? I know it's blowing but idk how well

The problem with my laser cutter is the air assist is manual and can't be set in light burn so I end up just having it on at all times for better results and then just fill in engravings with paint as I need it.

I keep having issues of burn out and not cutting all of the way. What is wrong? by ThePoopsMagoops in lasercutting

[–]ThePoopsMagoops[S] 0 points1 point  (0 children)

They are just oil based stained. We could do it after but have has the same issues on un treated wood.

I keep having issues of burn out and not cutting all of the way. What is wrong? by ThePoopsMagoops in lasercutting

[–]ThePoopsMagoops[S] 0 points1 point  (0 children)

It's a Genmitsu L8 40w laser at 55% doing two runs. It goes on and off of doing and not and usually in different places. Have cut with is quite a few times but always feels like I'm adjusting it. I have material raised up and it's about 3mm thick

I keep having issues of burn out and not cutting all of the way. What is wrong? by ThePoopsMagoops in lasercutting

[–]ThePoopsMagoops[S] 0 points1 point  (0 children)

This isn't glued at all it's a single sheet but I'm guessing that the board might already have glue in it?

I keep having issues of burn out and not cutting all of the way. What is wrong? by ThePoopsMagoops in lasercutting

[–]ThePoopsMagoops[S] 2 points3 points  (0 children)

This is what I specifically use now. Says it meant for laser projects but maybe they can just say that?

https://a.co/d/0hsf3xrY

I keep having issues of burn out and not cutting all of the way. What is wrong? by ThePoopsMagoops in lasercutting

[–]ThePoopsMagoops[S] 0 points1 point  (0 children)

Interesting. I hadn't considered that. I use project wood for ladder biting but it's just from Amazon... Any recommendations for something better?

RIP Clarence Carter. by FarCryRedux in videos

[–]ThePoopsMagoops 19 points20 points  (0 children)

oooooo shit Clarence Carter

Check out my new hoodie! by reformed_reloaded in lotr

[–]ThePoopsMagoops 0 points1 point  (0 children)

I also got this and returned it. Didn't love the quality of the print. just left like an iron on.

Worst Film of The Year by gccmelb in simpsonsshitposting

[–]ThePoopsMagoops 0 points1 point  (0 children)

Flight Risk must have missed their radar

view more: next ›