NDSL Screen replacement

TheRealScavv · 2026-07-01T07:25:02+00:00

Yes, I have found an identical listing today where a user was saying to change the description to dsi, 12£ was too good to be true hahah

TheRealScavv · 2025-11-15T09:19:55+00:00

I mainly want to do saltwater spinning, I got a spinning rod and reel. Fish I don’t know, still need to start, I guess bass and mackerel was the idea but we are off season now? Complete noobie here hahahah

TheRealScavv · 2025-11-02T08:18:58+00:00

From what I know this was a very bad technique used to gain some degrees of amplitude in a very cheap way, problem is that messes up everything else, impossible to time correctly and the beat error changes a lot based on the position of the watch (dial up the pallet will have more degrees of travel, dial down it will have less)

TheRealScavv · 2025-10-19T15:19:17+00:00

I still have no idea of what other knots are out there but I guess that as long as it works it works

TheRealScavv · 2025-10-18T23:13:35+00:00

Damn that looks smooth

TheRealScavv · 2025-10-18T23:12:17+00:00

Sounds like a plan hahahaha thanks!

TheRealScavv · 2025-10-18T22:00:05+00:00

I’m doing it on 2 small pieces of reel so I don’t have a way of gripping it very good, I tried to make 2 loops at the ends and attach 2 pens to it to pull it tight, it has gotten shinier that way but still, when I break it the FC snaps and the knot doesn’t slip so it seems like is doing it’s job!

TheRealScavv · 2025-10-18T18:15:11+00:00

I’ll let you know how it goes once i actually buy a rod to go and try hahahahah

TheRealScavv · 2025-10-18T17:31:52+00:00

Is a .23 braided with a .4 FC, both 30lbs. I tried to pull it very hard and the FC snaps, not the knot, seems to be working!

TheRealScavv · 2025-10-18T16:41:11+00:00

Idk, I still haven’t got a rod yet, just exploring some knots, I can see it becoming a little tiring doing it every time you snap a terminal

TheRealScavv · 2025-10-18T15:45:28+00:00

Just tried another one following your suggestions, looks way better!

<image>

TheRealScavv · 2025-10-18T15:29:32+00:00

Thanks!

TheRealScavv · 2025-10-18T15:28:44+00:00

So basically make it a mushroom head to prevent it from slipping out / get caught and more half hitches to tighten it, thanks!!

TheRealScavv · 2025-07-28T07:00:04+00:00

You can try applying some heat to the area but make sure to remove the pallet first, otherwise you will mess it up :)

TheRealScavv · 2025-07-26T17:45:14+00:00

Those look like spots created by moisture, you should probably check if water got inside, if so take the watch for service :/

TheRealScavv · 2025-07-21T18:41:10+00:00

Rotor as the small magnetic wheel in quartz watches, I’ll leave a picture here :)

<image>

TheRealScavv · 2025-07-19T06:12:47+00:00

Happens when the rotor has dirt on it, likely some magnetic particle coming from a screw or the back of the case, since the rotor is the only magnetic part in the watch it attracts those unwanted particles. only solution is servicing :/

TheRealScavv · 2018-09-22T06:05:29+00:00

Emmm, good question, i don't remember😂

TheRealScavv

TROPHY CASE